Abstract:The effects of a minor Zn addition on the mechanical and corrosion properties and microstructure of a high Mg content AlMg alloy containing Er and Zr in the warm-rolled state were studied using tensile test, nitric acid mass loss test (NAMLT), exfoliation corrosion susceptibility test (ASSET), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The tensile test results showed that the 0.58 wt% Zn addition to the Al-Mg-Er-Zr alloy increased the yield strength from 297 to 351 MPa and tensile strength from 416 to 445 MPa, but decreased the elongation from 13.3 % to 12.5 %. The NAMLT and ASSET results showed that the two warm rolled alloys were initially in the stabilization state, but the Al-Mg-Er-Zr alloy without Zn added became sensitized severely after the accelerated sensitization annealing (ASA) at 100 °C. The Zn addition improved the intergranular corrosion (IGC) resistance and exfoliation corrosion (EC) resistance significantly. The TEM results showed that, for the Al-Mg-Er-Zr alloy, there were Al 3 (Er,Zr) phase particles in the matrix and β (Al 3 Mg 2 ) phase particles separated from each other at the grain boundary. After the ASA treatment, more β phase particles were precipitated and covered the grain boundary completely. For the Al-Mg-Zn-Er- Zr alloy, another nanoscale T (Al 32 (Mg, Zn) 49 ) phase was precipitated in the matrix, and there were no grain boundary phase particles observed at the grain boundary, because the precipitation of T phase consumed the supersaturated Mg in the matrix, thus suppressing the formation of grain boundary phase particles during the ASA treatment and resulting in a good corrosion resistance. The strengthening effect of the Zn addition was mainly due to the formation of T phase particles during the warm rolling process.

Effect of Zn Addition on the Stress Corrosion Cracking of As-Cast BCC Mg-11Li Based Alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Correlations among stress corrosion cracking, grain-boundary microchemistry, and Zn content in high Zn-containing Al–Zn–Mg–Cu alloys

Effects of Cr and Zr additions on the microstructure and properties of Cu-6wt.% Ag alloys

Effect of Trace Zn on the Mechanical Properties and Corrosion Behavior of Al-Mg-Si Alloys with High Cu

Influence of Sc and Zr additions on microstructure and properties evolution of Al–Zn–Mg alloy

Influence of Zn Addition on the Aging Precipitate Behavior and Mechanical Properties of Al-Cu-Li Alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Investigating the Stress Corrosion Cracking of a Biodegradable Zn-0.8 Wt%li Alloy in Simulated Body Fluid

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

The influence of Zn addition on the microstructure and mechanical and corrosion properties of warm rolled Al mg alloys containing Er and Zr

Nanostructure Characteristics of Al3Sc1-xZrx Nanoparticles and Their Effects on Mechanical Property and SCC Behavior of Al-Zn-Mg Alloys

Influence of Minor Zn Addition on Precipitation Behavior and Intergranular Corrosion Properties of Al-Mg-Si Alloy

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

The Effect of Y/Er and Zn Addition on the Microstructure and Mechanical Properties of Mg-11Li Alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Microstructure and Mechanical Properties of As-Cast Al-10Ce-3Mg-xZn Alloys

Influence of Phase Dissolution and Hydrogen Absorption on the Stress Corrosion Cracking Behavior of Mg-7%Gd-5%Y-1%Nd-0.5%Zr Alloy in 3.5 Wt.% NaCl Solution