Abstract:Composites that use fly ash and slag as alkali-activated materials instead of cement can overcome the defects and negative effects of alkali-activated cementitious materials prepared with the use of an alkali-activated material. In this study, fly ash and slag were used as raw materials to prepare alkali-activated composite cementitious materials. Experimental studies were carried out on the effects of the slag content, activator concentration and curing age on the compressive strength of the composite cementitious materials. The microstructure was characterized using hydration heat, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM), and its intrinsic influence mechanism was revealed. The results show that increasing the curing age improves the degree of polymerization reaction and the composite reaches 77~86% of its 7-day compressive strength after 3 days. Except for the composites with 10% and 30% slag content, which reach 33% and 64%, respectively, of their 28-day compressive strength at 7 days, the remaining composites reach more than 95%. This result indicates that the alkali-activated fly ash–slag composite cementitious material has a rapid hydration reaction in the early stage and a slow hydration reaction in the later stage. The amount of slag is the main influencing factor of the compressive strength of alkali-activated cementitious materials. The compressive strength shows a trend of continuous increase when increasing slag content from 10% to 90%, and the maximum compressive strength reaches 80.26 MPa. The increase in the slag content introduces more Ca2+ into the system, which increases the hydration reaction rate, promotes the formation of more hydration products, refines the pore size distribution of the structure, reduces the porosity, and forms a denser microstructure. Therefore, it improves the mechanical properties of the cementitious material. The compressive strength shows a trend of first increasing and then decreasing when the activator concentration increases from 0.20 to 0.40, and the maximum compressive strength is 61.68 MPa (obtained at 0.30). The increase in the activator concentration improves the alkaline environment of the solution, optimizes the level of the hydration reaction, promotes the formation of more hydration products, and makes the microstructure denser. However, an activator concentration that is too large or too small hinders the hydration reaction and affects the strength development of the cementitious material.

Mechanical Properties and Durability of Alkali-Activated Fly Ash-Municipal Sludge Concrete

Activation and Toxicity of Slag-fly Ash-fluorgypsum Cementitious Material

Study of the Mechanical Properties and Microstructure of Alkali-Activated Fly Ash–Slag Composite Cementitious Materials

MSWI fly ash as alkaline cementitious material admixture

Strength characteristics of self-compacting concrete with alkali-activated fly ash

Design and Microstructural Analysis of the Mixture Proportion of Alkali-Activated Fly Ash-Slag Composite Cementitious Material

Early mechanical properties and strength calculation method of slag-based alkali activated concrete

Utilization of Mechanochemically Pretreated Municipal Solid Waste Incineration Fly Ash for Supplementary Cementitious Material

Microstructure, strength development mechanism, and CO2 emission analyses of alkali-activated fly ash-slag mortars

Mechanical and durability properties of slag/fly ash based alkali-activated concrete reinforced with steel, polypropylene and polyamide fibers

The Effect of Blast Furnace Slag/Fly Ash Ratio on Setting, Strength, and Shrinkage of Alkali-Activated Pastes and Concretes

An investigation on frost resistance and pore structure of alkali-activated slag concrete

Mechanical Properties of High Early Strength Class C Fly Ash-Based Alkali Activated Concrete

Research on strength and microscopic characteristics of lime-activated fly ash-slag solidified sludge under high temperature effect

Effect of fly ash and gypsum on drying shrinkage and mechanical properties of one‐part alkali‐activated slag mortar

Experimental Study on the Cracking Resistance at Early Ages of High Performance Concrete Added with Lithium Slag and Fly Ash

Study on Shrinkage in Alkali-Activated Slag–Fly Ash Cementitious Materials

A numerical study on chloride transport in alkali-activated fly ash/slag concretes

Microstructure and macro properties of sustainable alkali-activated fly ash mortar with various construction waste fines as binder replacement up to 100%

Evaluation of Fresh Properties of Controlled Low-Strength Material Produced from Water Treatment Sludge-Fly Ash-Slag Mixture Using Alkaline Activation

Effect of curing regime on the performance and microstructure characteristics of alkali-activated slag-fly ash blended concrete