Abstract:In the present paper, cracking sequence of high-strength engineered cementitious composite with the characteristic of low drying shrinkage (LSECC) under tension was experimentally studied by continually photographing during loading. The specific objective is to investigate the development of crack opening of each individual crack occurred during loading. Four Engineered cementations composite mixtures with water to binder ratio of 0.20, 0.25, 0.30, and 0.35 (LSECC-0.20, LSECC-0.25, LSECC-0.30, and LSECC-0.35) were used in the tests. Using the photographers taken during the test, crack width of each crack occurred during loading are determined according to the difference between solid material and crack on gray level. The test results show that cracks in ECC under tensile load are formed according to a temporal sequence. The opening width of each crack grows in a controllable and gradual manner with the increase of tensile strain. At a given strain level, crack width of different crack is not equal and the distribution of crack width is affected by matrix strength of the composite. Maximum crack width and the tensile strain capacity at the moment may be utilized to characterize the tensile performance of the composite that can guarantee both of tensile ductility and long-term durability. As maximum crack width equals 60 μm, at which the permeability of ECC may not be influenced by the cracks, higher strength ECC with water to binder ratio of 0.20 and 0.25 (LSECC-0.20 and LSECC-0.25) shows obvious higher tensile strain capacity and more cracks of narrow opening. By contrast, lower strength ECC with water to binder ratio of 0.30 and 0.35 (LSECC-0.30 and LSECC-0.35) shows relatively lower tensile strain and fewer cracks of narrow crack opening as crack width is limited below 60 μm. With the increase of tensile strain and the maximum crack width, much wider cracks (larger than 60 μm) are formed in lower strength ECC comparing to that of higher strength ECC.

Application of low drying shrinkage ECC in the protection layer of thermal insulation wall

Engineered Cementitious Composite with Characteristic of Low Drying Shrinkage

Tensile Properties of Low Shrinkage Engineered Cementitious Composite

Mapping of cracking sequence of polyvinyl alcohol-steel hybrid fiber reinforced high-strength engineered cementitious composite under uniaxial tension

Characteristics of High Ductility and Low Shrinkage Engineered Cementitious Composite and Its Applications

Engineered cementitious composites using blended limestone calcined clay and fly ash: Mechanical properties and drying shrinkage modeling

Evaluation of shrinkage induced cracking performance of low shrinkage engineered cementitious composite by ring tests

Matrix design for waterproof Engineered Cementitious Composites (ECCs)

Impact of Polyvinyl Alcohol Fiber on the Full Life-Cycle Shrinkage of Cementitious Composite

Weathering resistance of novel sustainable prefabricated thermal insulation wall

Experimental Study on the Interrelationship between the Moisture Content and Drying Shrinkage of Autoclaved Aerated Concrete Wallboard

Mechanical Performance of Low Shrinkage Engineered Cementitious Composite in Tension and Compression

Zeolite to Improve Strength-Shrinkage Performance of High-Strength Engineered Cementitious Composite

Flexural performance of novel ECC-RC composite sandwich panels

Numerical Study on Optimized Application of Engineered Cementitious Composites in RC Coupled Shear Wall Structures

Compression and Flexural Behavior of ECC Containing PVA Fiber

Bond Behavior and Failure Mechanisms of the Interface between Engineered Cementitious Composites and Shaped Steel

Durability Performance Investigation for Engineering Fiber Cementitious Composites (ECC): Review

Greener Engineered Cementitious Composite (ECC) – the Use of Pozzolanic Fillers and Unoiled PVA Fibers

Seismic Performance of Flexure-Dominated Reinforced-Engineered Cementitious Composites Coupled Shear Wall

An experimental study on the flexural properties of carbon textile reinforced ECC