Abstract:To explore the influence of the interface properties between fiber/cement matrix on the performance of fiber‐modified cement‐based composite. Polyethylene (PE) and polyvinyl alcohol fiber (PVA) are brought in the cement‐based materials to prepare mortar and Engineered Cementitious Composite (ECC) samples. The mortar's mechanical, and ECC's tensile capacity, four‐point bending and porosity were tested to verify the interface's influence on samples' performance. Furthermore, the water contact angle was used to analyze the wettability of the fiber, and a scanning electron microscope (SEM) was used to observe the fiber/matrix interface on the microscopic scale. Molecular dynamics simulation was performed to calculate the interfacial paraments from an atomic scale. The results shows that fiber increases the toughness of the mortar and improved its flexural strength. Through SEM, it was found that PVA fiber can form tight adsorption with the hydration matrix. While there are many apparent cracks and pores at the PE/matrix interface, the poor bonding destroys the matrix's structure and reduces its compressive strength. By analyzing the performance of ECC samples, it was known that PVA‐ECC's strain rate can reach 5.73%, while PE‐ECC is 4.20%. PE fiber has higher mechanical strength and can bear more loads, it helps PE‐ECC to obtain a greater modulus of rapture. Nuclear magnetic resonance results showed that the porosity of PVA‐ECC is lower than PE‐ECC. The ability of PE‐ECC to resist external interference is weak, and the interface of PE/matrix is easily damaged. Molecule dynamics simulation results indicated the adsorption energy between PVA/CSH is 6.17 times that of PE/CSH. The PVA/C‐S‐H interface tends to form CaO and H‐bonds to strengthen the bonding, the bonding has limited the movement of atoms and making the PVA chains tightly adsorbed on the CSH surface. While the adsorption between PE and CSH is weak, the PE will detach from the CSH surface and form aggregates. Moreover, PVA and water molecules form a stable hydrogen bond network to promote the hydration production grows on the surface of PVA fiber. However, PE fiber is complex enough to adsorb water molecules and hardly encourage the development of pores at the interface. By analyzing the properties of the interface between different fibers and cement matrix can provide insights for strengthening the interface properties of fiber cement matrix, and then improve the properties of fiber cement‐based composites.

Impact of Polyvinyl Alcohol Fiber on the Full Life-Cycle Shrinkage of Cementitious Composite

Compressive Behavior of Engineered Cementitious Composites under High Strain-Rate Loading

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

Research Progress and Performance Evaluation of Polyvinyl Alcohol Fiber Engineered Cementitious Composites

Influences of Fibers on Drying Shrinkage of Fiber-Reinforced Cementitious Composite

Effects of mix proportion and curing condition on mechanical properties of polyvinyl alcohol engineered cementitious composites

Mechanical Performance of Low Shrinkage Engineered Cementitious Composite in Tension and Compression

Effect of interfacial properties between polyethylene and polyvinyl alcohol fiber/cement matrix on properties of mortar and ECC

Properties of Polyvinyl Alcohol-Steel Hybrid Fiber-Reinforced Composite with High-Strength Cement Matrix

Uniaxial Tensile Experiment On Pva Fiber Reinforced Cementitious Composites

Drying Shrinkage Behavior of Ultra High Toughness Cementitious Composites and Its Influence on Anti-Cracking Capacity

Simulation and test of flexural performance of polyvinyl alcohol-steel hybrid fiber reinforced cementitious composite

Engineered cementitious composites using blended limestone calcined clay and fly ash: Mechanical properties and drying shrinkage modeling

Stress–Strain Properties and Gas Permeability Evolution of Hybrid Fiber Engineered Cementitious Composites in the Process of Compression

Compression and Flexural Behavior of ECC Containing PVA Fiber

Greener Engineered Cementitious Composite (ECC) – the Use of Pozzolanic Fillers and Unoiled PVA Fibers

Experimental Research on Tension Property of Polyvinyl Alcohol Fiber Reinforced Cementitious Composites

Evaluation of Engineered Cementitious Composites (ECC) containing Polyvinyl Alcohol (PVA) fibers under compressive, direct tensile, and drop-weight test

Durability Performance Investigation for Engineering Fiber Cementitious Composites (ECC): Review

Shrinkage, Permeation and Freeze–Thaw Characteristics of Ambient Cured High Calcium-Based Alkali-Activated Engineered Composites

Synergy Effect of Hybrid Steel-Polyvinyl Alcohol Fibers in Engineered Cementitious Composites: Fiber Distribution and Mechanical Performance