Abstract:To explore the effects of cutting speed, feed rate and rake angle on chip morphology transition, a thermomechanical coupled orthogonal (2-D) finite element (FE) model is developed, and to determine the effects of tool nose radius and lead angle on hard turning process, an oblique (3-D) FE model is further proposed. Three one-factor simulations are conducted to determine the evolution of chip morphology with feed rate, rake angle, and cutting speed, respectively. The chip morphology evolution from continuous to saw-tooth chip is described by means of the variations of chip dimensional values, saw-tooth chip segmental degree and frequency. The results suggest that chip morphology transits from continuous to saw-tooth chip with increasing feed rate and cutting speed, and changing a tool’s positive rake angle to negative rake angle. There exists a critical cutting speed at which the chip morphology transfers from continuous to saw-tooth chip. The saw-tooth chip segmental frequency decreases as the feed rate and the tool negative rake angle value increases; however, it increases almost linearly with the cutting speed. The larger negative rake angle, the larger feed rate and higher cutting speed dominate saw-tooth chip morphology while positive rake angle, small feed rate and low cutting speed combine to determine continuous chip morphology. The 3-D FE model considers tool nose radii of 0.4 mm and 0.8 mm, respectively, with tool lead angels of 0 deg and 7 deg. The model successfully simulates 3-D saw-tooth chip morphology generated by periodic adiabatic shear and demonstrates the continuous and saw-tooth chip morphology, chip characteristic line and the material flow direction between chip-tool interfaces. The predicted chip morphology, cutting temperature, plastic strain distribution, and cutting forces agree well with the experimental data. The oblique cutting process simulation reveals that a bigger lead angle results in a severer chip deformation, the maximum temperature on the chip-tool interface reaches 1289 deg, close to the measured average temperature of 1100 deg; the predicted average tangential force is 150N, with 7% difference from the experimental data. When the cutting tool nose radius increases to 0.8 mm, the chip’s temperature and strain becomes relatively higher, and average tangential force increases 10N. This paper also discusses reasons for discrepancies between the experimental measured cutting force and that predicted by finite element simulation.

Research on Cutting Temperature Distribution of Carbide Cutter Rake Face Considering Sticking-Welding Layer

Finite Element Simulation Of High-Speed Cutting Alloy Cast Iron

Study on the adhering failure mechanism of cemented carbide inserts and element diffusion model during the heavy-duty cutting of water chamber head

Finite Element Simulation of Orthogonal Cutting of H13-Hardened Steel to Evaluate the Influence of Coatings on Cutting Temperature

Theoretical Modeling of Cutting Temperature Distribution by Considering the Material Thermal Properties As Functions of Temperature

The Computer Simulation of the Temperature Distribution on the Surface of Ceramic Cutting Tools

The heat partition into cutting tool at tool-chip contact interface during cutting process: a review

A study investigating the cutting mechanism of compacted graphite iron based on a novel microstructure of finite element model

Analytical model of cutting temperature for workpiece surface layer during orthogonal cutting particle reinforced metal matrix composites

Analytical model of modified diamond tools temperature by focused ion beam in dry diamond turning

Predicting the Effects of Cutting Parameters and Tool Geometry on Hard Turning Process Using Finite Element Method

Simulation Analysis of the Influence of Coating on the Cutting Temperature Distribution Inside the Insert

3D Finite Element Simulation on High-speed Dry Hard Turning Process and Experiment Analysis

Predicting The Effects Of Tool Nose Radius And Lead Angle On Hard Turning Process Using 3d Finite Element Mothod

Coupled thermo-mechanical sticking-sliding friction model along tool-chip interface in diamond cutting of copper

Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

Analysis of High Temperature Wear Process Mechanism of Cemented Carbide Tool

Experiment Study on Cutter Disrepair Principle and Optimization for Machining Heat-Resistant Steel

Experimental research on the dynamic characteristics of the cutting temperature in the process of high-speed milling

Mechanisms and predictive force models for machining with rake face textured cutting tools under orthogonal cutting conditions

Investigations on Cutting Force and Temperature Field of Pick Cutter Based on Single Factor and Orthogonal Test Methods