Abstract:A comprehensive research project consisting of pilot-scale combustion testing and long-term laboratory corrosion study has been performed. A pilot-scale combustion facility was modified to enable burning of pulverized coals under the conditions typical for coal-fired utility boilers. Eight United States (U.S.) coals were selected for this investigation, with the test conditions for all coals set to have the same heat input to the combustor. In addition, the air/fuel ratio was controlled so that approximately 3% excess oxygen was attained in the combustion gas at the furnace outlet, a location equivalent to the furnace exit of commercial boilers. During each pilot-scale combustion test, extensive online measurements of the flue gas compositions were performed. In addition, deposit samples were collected at the same location for chemical analyses. This information characterized well the combustion environments adjacent to the superheaters and reheaters of utility boilers burning different U.S. coals. The gas and deposit compositions were then simulated in a series of 1000-hour laboratory corrosion tests in which the corrosion performances of different alloys were evaluated at 704oC (1300oF). Results of this laboratory study led to better understanding of the corrosion mechanisms operating on superheaters and reheaters in coal-fired boilers due to the mutual presence of sulfur and chlorine in coal. A new corrosion mechanism, i.e., “Active Sulfide-to-Oxide Corrosion Mechanism,” accounts for the rapid corrosion attack on low-alloy ferritic steels and lower-grade stainless steels resulting from the formation of iron chloride (FeCl2) vapor and associated cycling reactions. For higher alloys containing sufficient chromium, the attack is dominated by Hot Corrosion in the presence of a fused salt. In addition, two stages of the hot corrosion mechanism have been elucidated here in detail. The initiation of hot corrosion attack induced by molten sulfate may involve Stage 1 “acidic” fluxing and re-precipitation of the protective scale formed initially on the deposit-covered alloy surfaces, followed by Stage 2 Hot Corrosion dominated by “basic” fluxing and re-precipitation after the scale is locally penetrated by the fused salt.

High-temperature Corrosion Behavior of S30432 in High-Efficiency Ultra-Supercritical Boiler Burning Low-Alkali and High-Sulfur Coal

High‐temperature Corrosion Behavior of S30432 and TP310HCbN Coatings in Simulated 620°C Ultra‐supercritical Boiler Coal Ash/gas Environment

Fireside Corrosion Behaviors Of Super304h And Hr3c In Coal Ash/Gas Environment With Different So2 Contents At 650 Degrees C

Fireside Corrosion Behaviors of Super304H and HR3C in Coal Ash/Gas Environment with Different SO 2 Contents at 650 °C

Investigation on High Temperature Corrosion Characteristic of Super304H, TP347H, and HR3C Steel in an Ultra‐supercritical Coal‐fired Boiler▴

Investigation on High Temperature Corrosion of Water-Cooled Wall Tubes at a 300 MW Boiler

Investigation on Oxidation Behavior of Super304H and HR3C Steel in High Temperature Steam from a 1000 MW Ultra-Supercritical Coal-Fired Boiler

Investigation on slagging and high-temperature corrosion prevention and control of a 1000 MW ultra supercritical double tangentially fired boiler

High-Temperature Corrosion Properties of Boiler Steels under A Simulated High-Chlorine Coal-Firing Atmosphere

Intergranular corrosion susceptibility of a novel Super304H stainless steel

High-Temperature Corrosion Mechanisms for Selected Iron and Nickel-Based Alloys Exposed to Sulfur and Chlorine-Containing Environments

E303 CHARACTERISTICS OF HIGH-TEMPERATURE CORROSION AND FUEL-SULFUR MIGRATION IN METALLIC INTERFACE(Corrosion)

Study on High‐temperature Corrosion in a 600 MW Opposed Firing Boiler

Water Wall Tubes’ High Temperature Corrosion Root Cause Investigation: A 300 MW Level Boiler Case

Low-Temperature Ash Deposition and Dewpoint Corrosion of A Coal-Fired Travelling Grate Boiler

Evaluation and Improvement of the Coupled Effect of High-temperature Corrosion-erosion on Water Wall Tubes

Application study on enamel heat exchange tube in GGH of coal-fired units with ultra-low flue gas emission

Analysis and Solution of High-temperature Corrosion for a 1000 MW Ultra-supercritical Boiler

Formation of Sulfide Deposits and High-Temperature Corrosion Behavior at Fireside in a Coal-Fired Boiler

Materials for ultra-supercritical coal-fired power plant boilers

High-temperature corrosion data and mechanisms for T122, Super304H and HR3C after 15 years in 1000MW ultra-supercritical power plant