Abstract:In this study, the effect of TiCN and WC-Co coatings on the tribological performance of spheroidal graphite cast iron materials was investigated by wear tests under dry and lubricated conditions. The mechanical and physical effects of the coating processes were analysed by microhardness measurements and visual methods (SEM, EDX, XRD). The tribological effect of WC-Co and TiCN coated specimens were investigated by ball-on-plate wear tests carried out under dry and boron oil emulsion (5% concentration) conditions at 50 N load and 60 rpm sliding speed parameters. The friction coefficient and wear volume results were obtained to investigate the effect of the coating process and boron oil emulsion on friction and wear behaviour. The wear mechanisms were determined with SEM images obtained from the worn surfaces and surfaces analysed elementally with EDX images. Additionally, surface morphology was examined with surface roughness measurements and 2D–3D topography images. According to the microhardness measurement results, it was observed that the spheroidal graphite cast iron with 290 HV hardness reached 1559 HV with TiCN coating and 1440 HV with WC-Co coating. According to the wear test results, it was determined that TiCN and WC-Co coatings decreased the friction coefficient by 32.51% and 12.80%, respectively. When the effect of boron oil usage compared to dry environmental conditions, it was concluded that the friction coefficient and wear volume decreased by a maximum of 54.80% and 53.70%, respectively. Additionally, the roughness values decreased in the experiments where the boron oil emulsion was used. However, although the TiCN coating improved the surface quality, the WC coating negatively affected the surface quality. Surface form images obtained with 2D and 3D topography also support the alteration in roughness values.

Fabrication and Tribology Properties of Cr-Coated Cemented Carbide under Dry Friction Conditions

Tribological performance of DLC-coated ceramics against cemented carbide under dry sliding conditions

Tribological and dry drilling performance of WS2/Cr-AlCrN coatings

Fabrication and tribological properties of textured diamond coatings on WC-Co cemented carbide surfaces

High-temperature tribological properties of AlCrN coatings deposited on textured surfaces under dry friction

Study on the Friction-Reducing Mechanisms of Surface Texture Cemented Carbide under Dry Sliding

Preparation and Tribological Properties of Graphene-Based Coatings on Tungsten Carbide

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Effect of Substrates Characteristics on Tribological Behaviors of AlTiN-Based Coated WC–Co Cemented Carbides

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Microstructure and Tribological Properties of Multilayered ZrCrW(C)N Coatings Fabricated by Cathodic Vacuum-Arc Deposition

Study on the surface performance strengthening of AlCrN coated cemented carbide by micro-texture laser preparation process

Investigation of wear behavior of carbide based coated rolling roll materials under dry and lubricated conditions

Tribological characteristics of WC-Cr3C2-Ni cermet coatings under different wear parameters

Study on salt spray corrosion and friction wear performance of CrN coated cemented carbide sealing ring

Sliding friction behaviors of TiCN/Cr 3 C 2 -NiCr and TiCN/WC-CoCr duplex coatings fabricated by combining HVOF and HT-CVD procedures

Tribological Properties of Carbon-Fibre-reinforced Plastic Against Tungsten Carbide under Dry Condition

Combined Effect of a Laser Cladded Coating and Surface Texture on Tribological Performance Under Dry Sliding and Starved Lubrication

Microstructure and tribological properties of CrVN thin film coated WC‐Co tool after boriding process

Microstructure and wear resistance of bimodal cemented carbide coating prepared by direct laser powder deposition

Comparative tribological performance of a-C:H, ta-C and AlCrSiN coatings on 20CrMnTi gear steel under dry sliding condition