Abstract:In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 μm to 4.1 μm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 μm to 7.24 μm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.

Enhanced age-hardening of an Al-5Mg-2Zn-1Cu alloy by pre-aging combined with pre-straining

Effects of Mg/Zn ratio and pre-aging on microstructure and mechanical properties of Al–Mg–Zn–Cu alloys

The Effect of Pre-Ageing/stretching on the Ageing-Hardening Behavior of Al–Zn–Mg–Cu Alloys Correlated with Zn/Mg Ratio

Pre-Aging Effect on the Formation of Ω Phase and Mechanical Properties of the Al-Cu-Mg-Ag Alloy

Influence of Pre-Deformation on Age-Hardening Response and Mechanical Properties of Extruded Mg–6%Zn–1%Mn Alloy

Influence of Pre-Strain on the Aging Hardening Effect of the Mg-9.02Zn-1.68Y Alloy

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys under Multi-Directional Severe Strain and Aging

Synergistic Improvement of Strength and Ductility of an Ultra-High Strength Al-Zn-Mg-Cu Alloy Through a New Aging Strategy

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

Effects of Combined Pre-Straining and Pre-Aging on Natural Aging and Bakehardening Response of an Al-Mg-Si Alloy

Effects of Pre-Strain and Aging Treatments on the Mechanical Property and Corrosion Resistance of the Spray Formed Ultra-High Strength Al-Zn-Mg-Cu Alloy

Achieving Superior Strength-Ductility Balance by Tailoring Dislocation Density and Shearable GP Zone of Extruded Al-Cu-Li Alloy

Effect of Pre-strain on the Solute Clustering, Mechanical Properties, and Work-Hardening of a Naturally Aged Al-Cu-Mg Alloy

Effect of pre-deformation on microstructures and mechanical properties of high purity Al–Cu–Mg alloy

Achieving high strength-ductility of an Al–Mg–Si–Cu alloy via heterostructure coupling with pre-aging precipitation

Effects of aging treatment on the precipitation behaviors and mechanical properties of Al-5.0Mg-3.0Zn-1.0Cu cast alloys

Enhanced Heat Resistance of Al-Cu-Mg Alloy by a Combination of Pre-stretching and Underaging

Study on Microstructural Evolution and GP Zone Strengthening Mechanism by Solution and Aging Treatment in Non-dendritic Mg-6Zn-5Al Magnesium Alloy

Improved Mechanical Properties of Al-xMg-yZn-Cu Alloys Via Optimized Mg/Zn Ratio and Thermomechanical Processing