Abstract:It is an effective strategy to improve the performance of quasi-two-dimensional (Q-2D) perovskite solar cells (PSCs) by introducing fluoro-substituted aromatic alkylammonium spacer cations into the active layer. Herein, the influence of the benzylammonium (BA) and the x-fluorobenzylammonium (xFBA) cation, in which x stands for the substitution position of the benzene ring (o, ortho; m, meta; p, para), on the crystal orientation, phase distribution, film morphology of the Q-2D (n = 5) perovskite films, and the corresponding device performance is systematically evaluated. The result suggests that compared with BA and oFBA, mFBA and pFBA have a larger dipole moment, forming a dense perovskite film with gradient structures where the n = 1 2D perovskite mainly exists at the top of the film and the large n-phase perovskite exists at the bottom of the film. Encouragingly, the (pFBA)2MA4Pb5I16 (MA = CH3NH3+)-based perovskite solar cells achieve the highest efficiency of 17.12%, with an open-circuit voltage of 1.175 V, a short-circuit current density of 18.50 mA cm–2, and a fill factor of 78.78%, which is significantly higher than those of BA (14.07%)-, oFBA (12.89%)-, and mFBA (14.67%)-based PSCs. Furthermore, pFBA-based devices also exhibit the best stability compared to the other three devices.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.chemmater.2c00146.1H NMR spectra and molecular dipole moments of BAI, oFBAI, mFBAI, and pFBAI; UPS spectra of BA-, oFBA-, mFBA-, and pFBA-based n = 5 2D perovskite and the corresponding (αhv)2 vs hv curves of 2D perovskites; J–V curves of BA-, oFBA-, mFBA-, and pFBA-based Q-2D PSCs with forward and reverse scans; EDS mapping of different elements (C, N, I, Pb, Cl) of perovskite films with different cations; TA spectra for different n phases as a function of delay time of the four films; formation energy of the 2D perovskite corresponding to cations; series resistance (Rs), charge-transport resistance (Rct), and recombination resistance (Rrec) derived from EIS for different PSCs and VTFL form SCLC for different PSCs; and experimental crystallographic parameters of (oFBA)2PbI4 (PDF)This article has not yet been cited by other publications.

Strain relaxation and phase regulation in quasi-2D perovskites for efficient solar cells

In-situ compensation for thermal strain by phase transformation strain in all-inorganic perovskite solar cells

Tailored Phase Conversion under Conjugated Polymer Enables Thermally Stable Perovskite Solar Cells with Efficiency Exceeding 21.

Spacer Cation Tuning Enables Vertically Oriented and Graded Quasi‐2D Perovskites for Efficient Solar Cells

The strain regulation of atomic structure and properties on ultra-stable monolayer butylammonium-based halide perovskites: Insight from density functional theory

Interfacial Residual Stress Relaxation in Perovskite Solar Cells with Improved Stability

Facile lattice tensile strain compensation in mixed-cation halide perovskite solar cells

Dual‐Surface Polydentate Anchoring Enabled Strain Regulation for Stable and Efficient Perovskite Solar Cells

Suppressing the Photoinduced Halide Segregation in Wide‐Bandgap Perovskite Solar Cells by Strain Relaxation

High performance and stability of perovskite solar cells achieved through anti-solvent modulation of multi-orientation PbI 2 and stress relief

Band Alignment Boosts over 17% Efficiency Quasi-2D Perovskite Solar Cells via Bottom-Side Phase Manipulation

Highly Efficient and Stable Wide-Bandgap Perovskite Solar Cells Via Strain Management

Metastable interphase induced pre-strain compensation enables efficient and stable perovskite solar cells

Stress compensation based on interfacial nanostructures for stable perovskite solar cells

Strain release of formamidinium-cesium perovskite with imprint-assisted organic ammonium halide compensation for efficient and stable solar cells

Crystallinity Control and Strain Release in Wide-Bandgap Perovskite Film via Seed-Induced Growth for Efficient Photovoltaics

Quantum Well Growth Management to Smooth the Energy Transfer Pathway for Quasi‐2D Perovskite Solar Cells

Regulating the lattice strain in perovskite films to obtain efficient and stable perovskite solar cells

Selectively Fluorinated Benzylammonium-Based Spacer Cation Enables Graded Quasi-2D Perovskites for Efficient and Stable Solar Cells

Strain Engineering Toward High‐Performance Formamidinium‐Based Perovskite Solar Cells

Local nearly non-strained perovskite lattice approaching a broad environmental stability window of efficient solar cells