Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Quantum Well Growth Management to Smooth the Energy Transfer Pathway for Quasi‐2D Perovskite Solar Cells

Water‐Assisted Crystal Growth in Quasi‐2D Perovskites with Enhanced Charge Transport and Photovoltaic Performance

Two-Dimensional Perovskite Solar Cells with 14.1% Power Conversion Efficiency and 0.68% External Radiative Efficiency

High‐Efficiency Quasi‐2D Perovskite Solar Cells Incorporating 2,2′‐biimidazolium Cation

Spacer Cation Tuning Enables Vertically Oriented and Graded Quasi‐2D Perovskites for Efficient Solar Cells

Perovskite Quantum Wells Formation Mechanism for Stable Efficient Perovskite Photovoltaics—A Real‐Time Phase‐Transition Study

Single-Crystal-Assisted In Situ Phase Reconstruction Enables Efficient and Stable 2D/3D Perovskite Solar Cells

Regulation of phase arrangement in 2D ruddlesden-popper perovskite films via anti-solvent method for efficient solar cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Molecular Engineering for Two-Dimensional Perovskites with Photovoltaic Efficiency Exceeding 18%

Crystal Growth Regulation of 2D/3D Perovskite Films for Solar Cells with Both High Efficiency and Stability

Strain relaxation and phase regulation in quasi-2D perovskites for efficient solar cells

Orientation Regulation of Phenylethylammonium Cation Based 2D Perovskite Solar Cell with Efficiency Higher Than 11%

Concerted regulation on vertical orientation and film quality of two-dimensional ruddlesden-popper perovskite layer for efficient solar cells

High-performance quasi-2D perovskite solar cells with power conversion efficiency over 20% fabricated in humidity-controlled ambient air

The Second Spacer Cation Assisted Growth of a 2D Perovskite Film with Oriented Large Grain for Highly Efficient and Stable Solar Cells.

Highly Efficient and Stable Solar Cells Based on Crystalline Oriented 2D/3D Hybrid Perovskite

Modulation of Colloidal Assembly Behavior Enables Printable Low-Dimensional Perovskite Photovoltaics

Tailoring the Functionality of Organic Spacer Cations for Efficient and Stable Quasi‐2D Perovskite Solar Cells

Spontaneous Formation of Upper Gradient 2D Structure for Efficient and Stable Quasi‐2D Perovskites

Band Alignment Boosts over 17% Efficiency Quasi-2D Perovskite Solar Cells via Bottom-Side Phase Manipulation