Abstract:Purpose: The purpose of this study was to review the literature regarding the evolution of current thoughts on fixation of mandibular angle fractures (MAFs), based on in vitro biomechanical assessments and computer-based studies. Methods: An electronic search in PubMed was undertaken in August 2012. The titles and abstracts from these results were read to identify studies within the selection criteria. Eligibility criteria included studies from the last 30 years (from 1983 onwards). Results: The search strategy initially identified 767 studies. Thirty-one studies were identified without repetition within the selection criteria. Two articles showing significance in the development of treatment techniques was included. Additional hand searching yielded five additional papers. Thus, a total of 38 studies were included. Conclusions: The osteosynthesis positions as well as the plating technique play important roles in the stability of MAF repair. The only in vitro study evaluating the use of wire osteosynthesis concluded that wires placed through the lower border approach would provide greater stability than those at the upper border. Many studies indicate that the use of two miniplates avoids (or decreases) lateral displacement of the lower mandibular border and opening of the inferior fracture gap. Some studies even suggest that the use of two miniplates may be considered a more "rigid" fixation technique for MAFs than the use of a reconstruction plate. When using two miniplates, the biplanar plate orientation provides greater biomechanical stability than the monoplanar one. However, despite its greater biomechanical stability, the two-miniplate technique has some disadvantages that should also be taken into account. Studies with biodegradable plates suggest the use of at least two plates for each MAF. There are few studies with compression plates, and they have not yet reached a consensus. The solitary lag screw proved to withstand the functional loading of the mandible; however, only few biomechanical assessments were performed. In vitro studies have shown good biomechanical stability with the use of 3-D grid plates. The use of malleable miniplates alone is not sufficient to withstand the early postoperative bite force. Some studies suggest that the segment of the tension band miniplate located at the distal fragment of the MAF should be fixed with three screws. The studies also showed some limitations. None considered the stabilization of the fracture site afforded by the masseter-pterygoid muscle pouch. Most of the studies did not evaluate plating system strength in the long term and therefore did not observe the effect of resorption on the strength of the different biodegradable plating systems. Another limitation of many studies is the absence of a control group. A confounding factor that could not be tested in in vitro investigations is the additional resistance to displacement of jagged fracture margins present in the human fracture.

[Miniplate Osteosynthesis of Mandibular Fracture].

Evaluation of osteosynthesis of miniplate versus lag screw in management of mandibular angle fracture - A comparative study

Stability and Complications of Miniplates for Mandibular Reconstruction with a Fibular Graft: Outcomes for 544 Patients

Clinical evaluation and improvement on mini-plate fixation as tension band for mandibular angle fracture

The clinical investigation on the internal rigid fixation for the man dibular fractures of 268 cases

Biomechanical comparison of plate materials and designs for subcondylar fracture fixation: An assessment

Miniplate 1.5 fixation for the repair of mandibular osteotomies in cats

An in-vitro evaluation of a novel design of miniplate for fixation of fracture segments in the transition zone of parasymphysis-body region of mandible using finite element analysis

Comparison Between Conventional Titanium Miniplates and Indigenous Detachable Custom made 3D Titanium Plates (VAS 3D Bone Plate) for Fixation of Mandibular Fracture in Mental Foramen Region: A Randomized Clinical Trial and Finite Element Analysis

Comparision of the treatment effect on the different fixation for the mandibular fractures

Biomechanical Analysis and Comparison Between "Zeta" Miniplate Design & Conventional Miniplate System for Fixation of Fracture Segments in Transition Zone of Parasymphysis Body Region of Mandible – An In-Vitro Study

The Evaluation of Intraoral Incision and Rigid Internal Fixation in the Therapy of Jaw Fracture

Clinical Efficacy of Mini-Plate Fixation in the Treatment of Bennett Fractures

Fixation of mandibular angle fractures: in vitro biomechanical assessments and computer-based studies

Evaluation of labial versus labio-inferior lines of osteosynthesis using 3D miniplate for fractures of anterior mandible: A finite element analysis with a pilot clinical trial

Comparative Assessment of Clinical and Quality of Life Outcomes in Mandibular Angle Fractures Treated with Standard and Three-Dimensional Mini-Plates

Assessment of CAD/CAM Customized V Pattern Plate Versus Standard Miniplates Fixation in Mandibular Angle Fracture (Randomized Clinical Trial)

A Comparison of Lag Screw and Miniplate Fixation for the Anterior Mandibular Fractures

Treatment of mandible fractures: A retrospective clinical analysis of 148 cases

Biomechanical interactions of different mini-plate fixations and maxilla advancements in the Le Fort I Osteotomy: a finite element analysis

Comparative study of CAD/CAM reconstruction and miniplates for patient-specific fixation in LCL-type mandibular reconstruction