Abstract:Purpose: The purpose of this study was to review the literature regarding the evolution of current thoughts on fixation of mandibular angle fractures (MAFs), based on in vitro biomechanical assessments and computer-based studies. Methods: An electronic search in PubMed was undertaken in August 2012. The titles and abstracts from these results were read to identify studies within the selection criteria. Eligibility criteria included studies from the last 30 years (from 1983 onwards). Results: The search strategy initially identified 767 studies. Thirty-one studies were identified without repetition within the selection criteria. Two articles showing significance in the development of treatment techniques was included. Additional hand searching yielded five additional papers. Thus, a total of 38 studies were included. Conclusions: The osteosynthesis positions as well as the plating technique play important roles in the stability of MAF repair. The only in vitro study evaluating the use of wire osteosynthesis concluded that wires placed through the lower border approach would provide greater stability than those at the upper border. Many studies indicate that the use of two miniplates avoids (or decreases) lateral displacement of the lower mandibular border and opening of the inferior fracture gap. Some studies even suggest that the use of two miniplates may be considered a more "rigid" fixation technique for MAFs than the use of a reconstruction plate. When using two miniplates, the biplanar plate orientation provides greater biomechanical stability than the monoplanar one. However, despite its greater biomechanical stability, the two-miniplate technique has some disadvantages that should also be taken into account. Studies with biodegradable plates suggest the use of at least two plates for each MAF. There are few studies with compression plates, and they have not yet reached a consensus. The solitary lag screw proved to withstand the functional loading of the mandible; however, only few biomechanical assessments were performed. In vitro studies have shown good biomechanical stability with the use of 3-D grid plates. The use of malleable miniplates alone is not sufficient to withstand the early postoperative bite force. Some studies suggest that the segment of the tension band miniplate located at the distal fragment of the MAF should be fixed with three screws. The studies also showed some limitations. None considered the stabilization of the fracture site afforded by the masseter-pterygoid muscle pouch. Most of the studies did not evaluate plating system strength in the long term and therefore did not observe the effect of resorption on the strength of the different biodegradable plating systems. Another limitation of many studies is the absence of a control group. A confounding factor that could not be tested in in vitro investigations is the additional resistance to displacement of jagged fracture margins present in the human fracture.

Biomechanical interactions of different mini-plate fixations and maxilla advancements in the Le Fort I Osteotomy: a finite element analysis

Biomechanical Evaluation of Chinese Customized Three-Dimensional Printed Titanium Miniplate in the Lefort I Osteotomy: A Finite Element Analysis

Comparison of the Biomechanical Behavior Between Commercial and 3D-Printed Patient-Specific Ti6Al4V L-Shaped Titanium Plates Following Le Fort I Osteotomy Using Finite Element Analysis: A Technical Note

An in-vitro evaluation of a novel design of miniplate for fixation of fracture segments in the transition zone of parasymphysis-body region of mandible using finite element analysis

Biomechanical evaluation of reconstruction of the posterior complex in restorative laminoplasty with miniplates

Evaluation of labial versus labio-inferior lines of osteosynthesis using 3D miniplate for fractures of anterior mandible: A finite element analysis with a pilot clinical trial

Comparative Biomechanical Stability of the Fixation of Different Miniplates in Restorative Laminoplasty after Laminectomy: A Finite Element Study

Biomechanical comparison of plate materials and designs for subcondylar fracture fixation: An assessment

Finite element analysis of a novel anatomical plate in posterolateral plateau fractures

Biomechanical Analysis and Comparison Between "Zeta" Miniplate Design & Conventional Miniplate System for Fixation of Fracture Segments in Transition Zone of Parasymphysis Body Region of Mandible – An In-Vitro Study

Experimental validation of finite element simulation of a new custom-designed fixation plate to treat mandibular angle fracture

Biomechanical study of two-level oblique lumbar interbody fusion with different types of lateral instrumentation: a finite element analysis

Fixation Methods for Mandibular Advancement and Their Effects on Temporomandibular Joint: A Finite Element Analysis Study

Postoperative maxillary stability after Le Fort I osteotomy using a u-HA/PLLA system: three-dimensional analysis by surface superimposition based on virtual Le Fort I osteotomy

Finite element analysis of different titanium miniplates: Evaluation of three-dimensional designs applied on condylar neck fractures

Biomechanical evaluation on a new type of vertebral titanium porous mini-plate and mechanical comparison between cervical open-door laminoplasty and laminectomy: a finite element analysis

[Miniplate Osteosynthesis of Mandibular Fracture].

Stability and Complications of Miniplates for Mandibular Reconstruction with a Fibular Graft: Outcomes for 544 Patients

Comparative study of CAD/CAM reconstruction and miniplates for patient-specific fixation in LCL-type mandibular reconstruction

Fixation of mandibular angle fractures: in vitro biomechanical assessments and computer-based studies

Stability of different fixation methods after reduction malarplasty under average and maximum masticatory forces: a finite element analysis