Abstract:This paper describes the main results from an experimental investigation into the thermal stability of a cold-rolled Al–Y alloy. Tensile tests performed on specimens of the alloy and pure Al in annealed states reveal superior anti-softening properties of the former specimens relative to the latter counterparts. Origins of such thermal stability and underlying recovery and recrystallization kinetics are studied using electron microscopy and high energy X-ray diffraction (HEXRD) techniques. Microscopic observations reveal that recovery and recrystallization begin in the specimens of pure Al at a much lower temperature than in the specimens of Al–Y alloy. Onset of the recovery process in the Al–Y alloy is observed to begin with dislocation rearrangements in the β-Al3Y phases. The onset is followed by more substantial reduction in dislocation density, shrinkage of the β-Al3Y phases, and coarsening of the α-Al grains. The alloy contains stacking faults, which interestingly remain stable during the annealing treatments contributing to the thermal stability. The observed mechanisms are further confirmed by tracking the evolution of peaks under the in-situ synchrotron X-ray diffraction with heating. Onset of recovery was observed at 280 °C in both α-Al and β-Al3Y phases, while substantial shrinkage and spheroidization of β-Al3Y phases and decrease in dislocation density were detected at 400 °C causing loss of the alloy strength. Thermodynamic calculation showed that solubility of Y rapidly increases in α-Al at temperatures above 400 °C explaining the spheroidization and shrinkage of the β-Al3Y phases by diffusion of Y into the Al matrix.

Overheating Structure and Mechanical Properties of YL12 Al-alloy

Effect of melt overheating treatment on the microstructure and mechanical properties of Zn–Al alloy

Microstructure And Mechanical Properties Of Mg-12.3zn-5.8y-1.4al Alloy

Mechanical Behavior and Failure Mechanism of an As-Extruded Mg-11 Wt％y Alloy at Elevated Temperature

Outstanding Thermal Stability of Cold-Rolled Al–Y Alloy Revealed Using In-Situ Synchrotron X-ray Diffraction and Ex-Situ Microscopy

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Microstructural evolution and mechanical property of Al–Zr and Al–Zr–Y alloys

Temperature Dependence of Mechanical Strength in HPDC Mg–6Y–3Zn–1Al Alloy with LPSO Phase

Effect of heat treatment on microstructure and dimensional stability of ZL114A aluminum alloy

Effect of Overheating Events on Microstructure and Low-Cycle Fatigue Properties of a Nickel-Based Single-Crystal Superalloy

Thermal Stability of Zr55Al10Ni5Cu30 Bulk Amorphous Alloy During Continuous Heating and Isothermal Annealing

Effects of Solution Temperature on Microstructures and Properties of Ti-23Al-25Nb-0.36Y Alloy

Microstructure Effects on Tensile Brittleness of As-Quenched Zl205A at Elevated Temperature

Effects of Yttrium on Microstructure and Properties of Ti-23Al-25Nb Alloy after Heat Treatment

Temperature-Dependent Mechanical Behaviors and Deformation Mechanisms in a Si-Added Medium-Entropy Superalloy with L12 Precipitation

Effect of yttrium addition on microstructural evolution and high temperature mechanical properties of Ni-based superalloy produced by selective laser melting

Influence of Heat Treatment on Microstructure and Mechanical Properties of Mg-10gd-3y-1.2zn-0.4zr Alloy

A comparative study on the microstructure and performance stability of Cu-Al2O3 and Cu-Y2O3 alloys after high-temperature annealing

Influence of Heat Treatment on Microstructure and Mechanical Properties of As-Cast Mg–8Li–3Al–2Zn–xY Alloy with Duplex Structure

Effect of Overheating Treatment on Microstructure and Stress Rupture Properties of a Nickel-Based Single-Crystal Superalloy

Effect of thermal exposure on the microstructure and mechanical properties of Ti60 alloy