Abstract:Laser Powder Bed Fusion (L-PBF) provides great advantages in creating supersaturated solid solutions due to its intrinsic ultrafast cooling and high solidification rate, which is particularly desired for enhanced solid solution strengthening and precipitation strengthening. In the present work, a novel high strength Zr/Sc/Hf-modified Al-Mn-Mg alloy with a good L-PBF processability is investigated. The as-built alloy exhibits a heterogeneous microstructure featuring a bi-modal grain structure with coarse columnar and fine equiaxed grains and heterogeneously distributed nanometer and submicrometer-sized cuboid-shaped primary Al3(Sc,Zr,Hf) particles. The Al3(Sc,Zr,Hf) phase, exhibiting a homogeneous elemental distribution of Zr, Sc, and Hf, adopts a cubic L12 structure with a lattice parameter of 0.4044 ± 0.009 nm, showing a good coherency with α-Al. Additionally, the rapid L-PBF solidification enables the formation of submicrometer-sized elongated and globular primary Al6Mn and a supersaturated Al matrix with a high dislocation density. This results in a good combination of strength (yield strength of 438 ± 3 MPa and ultimate tensile strength of 504 ± 2 MPa) and ductility (elongation at fracture of 10.9 ± 1.4 %), with a moderate work hardening strength of 113 ± 12 MPa. Direct-ageing at 325 °C for 10 h promotes the formation of a large amount of rod-shaped Al6Mn precipitates and a few spherical Al3(Sc,Zr,Hf) nanoprecipitates. The heat treatment increases the hardness from 166 ± 2 HV in as-built condition to 173 ± 4 HV and enhances the tensile strength (yield strength of 487 ± 2 MPa and ultimate tensile strength of 542 ± 3 MPa) but slightly reduces the ductility to 7.4 ± 0.7 %. The high strength was achieved by the synergistic effect of grain boundary strengthening, solid solution strengthening, and Orowan strengthening mechanisms.

A High Strength Near-Eutectic Al-Mg-Si Alloy Manufactured by Laser Powder Bed Fusion

Microstructure and Mechanical Properties of Pseudo Binary Eutectic Al-Mg2Si Alloy Processed by Laser Powder Bed Fusion

Design high-strength Al-Mg-Si alloy fabricated by laser powder bed fusion: Cracking suppression and strengthening mechanism

Laser Powder Bed Fusion of a Novel High Strength Al-Mg Alloy Via Si and Zn Microalloying

Microstructural Evolution and Strengthening Mechanisms of a High-Strength Al-Mg-Si Alloy Processed by Laser Powder Bed Fusion and Ageing Treatment

High strength Al-Cu-Mg based alloy with synchronous improved tensile properties and hot-cracking resistance suitable for laser powder bed fusion

Developing a Novel High-Strength Al–Mg–Zn–Si Alloy for Laser Powder Bed Fusion

A crack-free and high-strength Al-Cu-Mg-Mn-Zr alloy fabricated by laser powder bed fusion

A Novel Al-Zn-Mg-Cu-Si-Zr-Er Alloy Fabricated by Laser Powder Bed Fusion

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

A high Fe-containing AlSi12 alloy fabricated by laser powder bed fusion

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

On the Si-induced microstructure evolution, solidification cracking healing and strengthening behavior of laser powder bed fusion additive manufactured Al-Cu-Mg/Si alloys

From Crack-Prone to Crack-Free: Eliminating Cracks in Additive Manufacturing of High-Strength Mg2Si-modified Al-Mg-Si Alloys

Manipulating Microstructure and Mechanical Properties of Laser Powder Bed Fusion Processed Hypo-Eutectic Al-13.3Mg2Si Alloy Via Annealing

Achieving High Strength in Laser Powder-Bed Fusion Processed AlFeCuZr Alloy Via Dual-Nanoprecipitations and Grain Boundary Segregation

Manipulating microstructure and mechanical properties of laser powder bed fusion processed hypo-eutectic Al-13.3Mg 2 Si alloy via annealing

Microstructural Origin of High Strength and High Strain Hardening Capability of a Laser Powder Bed Fused AlSi10Mg Alloy

Development of a high strength Zr/Sc/Hf-modified Al-Mn-Mg alloy using Laser Powder Bed Fusion: Design of a heterogeneous microstructure incorporating synergistic multiple strengthening mechanisms

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance