Abstract:The non-equilibrium phase evolution during laser powder bed fusion (LPBF) of AlSi10Mg alloy is thoroughly characterized and analyzed by means of advanced electron microscopy and analytical simulation of rapid solidification phenomenon. The evolution of microstructural strengthening agents such as inter-cellular eutectic phase and intra-cellular precipitates is presented in correspondence with the local variation of cellular/dendritic solidification patterns within a typical melt pool. The eutectic phase exhibits two different morphologies: lamellar and fibrous. As with the cell size variation, the overall volume fraction of eutectic phase and the lamella spacing is shown to gradually decrease by moving away from the melt-pool boundary (MPB), i.e., through crossing over from a coarse to a fine cellular zone. The eutectic-free regions within the α-Al cells contain a large number density of nano-sized precipitates that are predominantly Si-rich and are either fully or semi-coherent with the Al matrix. The formation of nano-precipitates is linked to the increased (non-equilibrium) solubility limits of α-Al cells due to the rapid solidification effect. For the first time, we identify such nano-precipitates with non-equilibrium crystal structures and morphologies: "Spheres" and "Ellipsoids" with Face Centered Cubic (FCC), and "Plates" and "Needles" with a Diamond Cubic (DC) superlattice structure that emerges from within the Al matrix. The microstructure in the heat-affected zone (HAZ) right underneath the MPB exhibits an absence of cell boundaries and eutectic phases while consisting primarily of large Si-rich and Mg-rich precipitates. Finally, the local variation of nano-hardness across a solidified melt pool is shown to correlate well with the corresponding profile of microstructural refinement, i.e., exhibiting a minimum at the HAZ and a peak at around the melt-pool centerline. The findings here can significantly advance the state of knowledge for the strengthening behavior in an as-built LPBF-processed AlSi10Mg alloy.

Manipulating microstructure and mechanical properties of laser powder bed fusion processed hypo-eutectic Al-13.3Mg 2 Si alloy via annealing

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Effect of Annealing on Anisotropic Tensile Properties of Al–12%Si Alloy Fabricated by Laser Powder Bed Fusion

Effect of heat treatment on the microstructure and mechanical properties of an Al-5Mg2Si-2Mg alloy processed by laser powder bed fusion

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Effect of Ti microalloying and laser remelting on the microstructure and mechanical properties of laser powder bed fusion Al-12Si alloy

Processing defect, microstructure evolution and mechanical properties of laser powder bed fusion Al-12Si alloys

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

The effect of the iso‐thermal heat treatment on the microstructure and properties of powder bed fusion‐laser beam AlSi10Mg alloy

Stress-relief annealing friendly Fe-based metallic glass-reinforced Al-Si-Mg-Zr alloy fabricated by laser powder bed fusion

Softening kinetics and mechanism during the annealing of an Al-Si alloy produced by laser powder bed fusion

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion

Superstrengthening Effect of Beyond-Solid-Solution Laser Powder Bed Fused We43 Magnesium Alloy Triggered by Direct Aging Treatment

Rapid Solidification and Non-equilibrium Phase Constitution in Laser Powder Bed Fusion (LPBF) of AlSi10Mg Alloy: Analysis of Nano-precipitates, Eutectic Phases, and Hardness Evolution

Microstructure, mechanical properties, and deformation behaviour of LPBF 316L via post-heat treatment

Simultaneously enhanced strength and ductility of AlSi7Mg alloy fabricated by laser powder bed fusion with on-line static magnetic field

Machine-Learning Assisted Laser Powder Bed Fusion Process Optimization for AlSi10mg: New Microstructure Description Indices and Fracture Mechanisms

A high Fe-containing AlSi12 alloy fabricated by laser powder bed fusion

Assessing the thermal stability of laser powder bed fused AlSi10Mg by short-period thermal exposure

Heterogeneous microstructure and mechanical behaviour of Al-8.3Fe-1.3V-1.8Si alloy produced by laser powder bed fusion