Abstract:BaTiO3 (BT) nanoparticles were prepared by the hydrothermal technique using different starting materials and the microstructure examined by XRD, SEM, TEM and HRTEM. X-ray diffraction and electron diffraction patterns showed that the nanoparticles were the cubic BaTiO3 phase. The BT nanoparticles prepared from the starting materials of as-prepared titanium hydroxide and barium hydroxide have spherical grain morphology, an average size of 65 nm and a fairly narrow size distribution. A uniform diffraction contrast across each single grain is observed in the TEM images, and the clear lattice fringes (with d(110) = 0.28 nm) observed in HRTEM images reveal that well-crystallized BT nanoparticles are synthesized by the hydrothermal method. The edges of the particles are very smooth, with no surface steps. BT nanoparticles with average grain size of 90 nm, synthesized using barium hydroxide and titanium dioxide as the starting materials, show surface facets. In this case a bimodal size distribution of large faceted and smaller particles is observed. Diffraction contrast variation across the particles caused by high strains within the particles is clearly observed. The high strains obviously stem from structural defects formed during hydrothermal synthesis, presumable in the form of lattice OH- ions and their compensation by cation vacancies. HRTEM images demonstrate that surface facets parallel to the (100) and (110) planes and small islands with 3 similar to 4 atomic layer thickness are frequently observed around the edge of the particles.

Microwave Synthesis of BaTiO<sub>3</sub> from BaCO<sub>3</sub> and TiO<sub>2</sub>

Microwave synthesis of BaTiO3 from BaCO3 and TiO 2

Effects of (mg1/3nb2/3) Substitution on the Structure and Microwave Dielectric Properties of Sr2TiO4 Ceramics

Room-Temperature Synthesis of BaTiO<sub>3</sub>Nanoparticles in Large Batches

Influence of Annealing Temperature on Microstructure and Phase Transformations of Oxide System Bi2O3/TiO2 Formed in Aqueous Solutions

Room temperature synthesis of BaTiO3 nanoparticles using titanium bis(ammonium lactato) dihydroxide

Molten-salt Synthesis of BaTiO3 Powders and Their Atomic-Scale Structural Characterization

Low-temperature Synthesis of TiB2 Nanocrystals Using TiO2 ,LiBH4 and Mg

Synthesis of nanocrystalline TiB2 powder from TiO2, B2O3 and Mg reactants through microwave-assisted self-propagating high-temperature synthesis method

Synthesis and Characterization of BaTiO3 Nanopowders Via Solvothermal Method

Direct Synthesis of Ultrafine Tetragonal BaTiO3 Nanoparticles at Room Temperature

Microstructural Characterization of BaTiO<sub>3</sub> Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Synthesis of barium strontium titanate nanopowders by microwave hydrothermal method

Preparation of Nanoscaled BaTiO3 Powders by DSS Method Near Room Temperature under Normal Pressure

Ba 4 Ti 13 O 30 Nanocrystals Prepared by Hydrothermal Method

Accelerated sintering and phase transformation of TiO<sub>2</sub> in microwave radiation

Ferroelectric properties and microwave sintering of BaTiO3 synthesized by using the alkoxide-hydroxide sol-gel process

Formation mechanism of BaTiO3nanocrystalline synthesized at room temperature

Accelerated sintering and phase transformation of TiO2in microwave radiation

Accelerated sintering and phase transformation of TiO 2 in microwave radiation

Microstructural Characterization of BaTiO3 Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Microwave Synthesis of BaTiO&lt;sub&gt;3&lt;/sub&gt; from BaCO&lt;sub&gt;3&lt;/sub&gt; and TiO&lt;sub&gt;2&lt;/sub&gt;