Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Novel Blasting-Like Lubricating Process for Cold Extrusion

Manipulation Tribological Behavior of Ti6Al4V Alloy Via a Duplex Treatment of Double Glow Plasma Surface Molybdenizing-Laser Surface Texturing (LST)

Combining Carbon Nanoparticle Coatings and Laser Surface Texturing for Enhanced Lubricity Under High Loads

Tribological Properties of Groove-Textured Ti-6Al-4V Alloys with Solid Lubricants in Dry Sliding against GCr15 Steel Balls

A novel current-carrying lubrication in electric hot incremental forming of Ti–6Al–4V titanium sheet

Friction-Induced Hardening Behaviors and Tribological Properties of 60niti Alloy Lubricated by Lithium Grease Containing Nano-BN and MoS2

A Novel Method for Determining Friction in Cold Forging of Complex Parts Using a Steady Combined Forward and Backward Extrusion Test

Analysis of the lubrication process with composition of solid lubricants of laser-modified sliding surfaces

Effects Of Polymer Composited Lubricant Coating On Tribological Properties Of Low-Carbon Steel Surface

Towards eliminating friction and wear in plain bearings operating without lubrication

Study on the Self-Organization of an Fe-Mn-C-B Coating during Friction with Surface-Active Lubricant

Surface nanocrystallized structural steel with enhanced tribological properties under different sliding conditions

Tribological Behaviors of Steel Surfaces Treated with Ion Sulphurization Duplex Processes

One-step preparation of high performance Ni-MoS2 self-lubricating coatings via jet electrodeposition on additive manufactured aluminum alloy

Controllable in situ fabrication of self-lubricating nanocomposite coating for light alloys

Long-Term Lubrication at 500 °C Using Continuously Replenishable Solid Lubricating Film Polymerized in Situ by Gasified Monomers PA and PPD

In-Situ Observation and Discrete Element Simulation of Solid Graphite Lubrication Mechanism

Lubricating Mechanism of Sulfurized Olefin on Ni-P Brush Plating Layer

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings

Synergetic effect of oleophilic textured surfaces and MoS 2 on the tribological properties of Ti-6Al-4V alloy under dry and lubricated sliding conditions

Tribo-induced Evolution of Nodular Supporting Structures Providing High-Performance Solid Lubricants in Carbon Nanotube Coated Films