Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

Electrochemical Properties of Mg 3 MnNi 2 - X % Polymethyl Methacrylate-Multiwalled Carbon Nanotubes (Pmma-Mwcnts) ( X = 25, 50, 75, 100)

Electrochemical properties of Mg3MnNi2- x% polymethyl methacrylate-multiwalled carbon nanotubes (PMMA-MWCNTs) ( x = 25, 50, 75, 100)

Electrochemical Properties of Cemg12+X%Ni Composites (X=0 Similar to 200) Prepared by Ball-Milling

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

Electrochemical properties of Mg-based alloys containing carbon nanotubes

Effects of Surface Modification on the Electrode Behavior of Amorphous CeMg12 Alloys

The electrochemical properties of MgNi– x wt% TiNi 0.56 Co 0.44 ( x = 0, 10, 30, 50) composite alloys

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Effects of Surface Modification on the Electrode Behavior of Ball-Milled La2Mg17 + 200 Wt% Ni Composite in Alkaline Solution

Electrochemical Performance of the Ball-Milled La2Mg14−xTixNi3 Alloys with Ni Powders (x=1 and 2)

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Electrochemical Hydrogen Discharge Properties of MgNi-Carbon Nanotube Composites

Microstructure and Electrochemical Properties of Mechanically Ground Ce2Mg17 + X Wt.% Ni (x = 0, 50, 100, 200) Composites

Influence of the material processing on the electrochemical properties of cobalt-free Ml(NiMnAlFe)5 alloy

Enhancement of Electrochemical Characteristics of Mg2ni/Mmni(5-X)(Coalmn)(X) by Forming Nano-Phase

The electrochemical properties of MmNi3.6Co0.7Al 0.3Mn0.4 alloy modified with carbon nanomaterials by ball milling

Electrochemical Properties of Cemg11ni+X% Ni Composites (X=0, 50, 100 and 200) Prepared by Ball-Milling

Electrochemical properties of MmNi3.6Co0.7Al0.3Mn0.4 alloy containing carbon nanotubes

Preparation and Electrochemical Characteristics of MgNi-TiNi<SUB>0.56</SUB>M<SUB>0.44</SUB>（M=Al,Fe）Alloys: Preparation and Electrochemical Characteristics of MgNi-TiNi<SUB>0.56</SUB>M<SUB>0.44</SUB>（M=Al,Fe）Alloys