Abstract:A shaping test of CuSn10 powders was carried out by using the selective laser melting (SLM) technology to study influences of process parameters of SLM on compactness of specimens. Meanwhile, process parameters were optimized based on the response surface methodology. Meanwhile, phase composition and microstructure of formed part were analyzed by XRD and OM. Results demonstrated that as the energy density of laser body increases from 146.7 J·mm -3 to 181.3 J·mm -3 , pores of samples decrease and the compactness increases from 98.97% to about 99.7%. Subsequently, the compactness begins to decrease with the continuous increase of laser energy density. The incomplete melting of powder under low energy density and gasification of powders under high energy density are major factors that influence the compactness. Over low or high laser energy density is disadvantageous for the improvement of compactness. A mathematical model of interaction between three factors (laser power, laser scanning speed and scanning space) and response value (compactness) was built up by using the BBD principle design test of response surface methodology. The degree of fitting (R 2 ) and correction coefficient (R 2 adj ) of the model were 0.9952 and 0.9866, which agree well with the fitting degree of experimental tests. Among three factors, influences of laser power and scanning speed on compactness are equivalent and more significant than scanning space. The optimal process parameters which were predicted by the model were laser power=331.471 W, scanning speed=648.045 mm·s -1 , scanning space=69.9302 μm. Under this circumstance, the compactness of CuSn10 powders after SLM is 99.75%. According to experimental verification, the practical value of compactness is 99.74%, showing a very small relative error. This proves that the BBD model is reliable. The shaped part is mainly composed of α-Cu phase and metastable phase β'-Cu13.7Sn. Compared with the original powders, the content of metastable phase β' increases significantly, while the δ-Cu41Sn11 phase disappears.

Metallic Powder Synthesized by Ultrasound-Assisted Electrical Discharge: Parametric Optimization-Based Isight Platform and Feasible Micro-fabrication Sintering

Controllable Synthesis of Hierarchical Micro/nano Structured FePO4 Particles under Synergistic Effects of Ultrasound Irradiation and Impinging Stream

The numerical research on the effect of ultrasonic field on metallic powders produced by the ultrasonic-assisted electrical discharge process

Solid-state production of uniform metal powders for additive manufacturing by ultrasonic vibration machining

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Influence of Electrical Parameter on the Size of Superalloy Powders Prepared by Spark Plasma Discharge Process

Powder-size driven facile microstructure control in powder-fusion metal additive manufacturing processes

Focusing Effect of Electromagnetic Fields and Its Influence on Sintering During the Microwave Processing of Metallic Particles

Structural Optimized Design of a Powder Mixer for Multi-Material Directed Energy Deposition Based on CFD-DPM

A Novel Ultrasonic Atomization Process For Producing Spherical Metal Powder

3D Online Submicron Scale Observation of Mixed Metal Powder's Microstructure Evolution in High Temperature and Microwave Compound Fields

Ultrasonic Preparation of Submicron Low Melting Point Alloy Powder

Process Parameter Optimization on Selective Laser Melting of CuSn10 Powders Based on Response Surface Methodology

Effect of Interface Behavior between Particles on Properties of Pure Al Powder Compacts by Spark Plasma Sintering.

Non-equilibrium solidification behavior associated with powder characteristics during electron beam additive manufacturing

Non-Equilibrium Solidification Behavior With Solute Trapping Associated With Powder Characteristics During Electron Beam Additive Manufacturing

Tailoring metal powders by dry nanoparticle coating for powder bed fusion applications

Multi-scale phase-field modeling of layer-by-layer powder compact densification during solid-state direct metal laser sintering

Factors affecting particle characterization of powders used in additive manufacturing

Making Nanostructured Ceramics from Micrometer-Sized Powders via Grain Refinement During SPS Sintering

Fabrication of BiInSn alloy powder via the combination of ultrasonic crushing with dispersants