Abstract:The copper crystal cone-shaped micro-nanostructure is used as the substrate, and the Ni-W alloy layer and Au nanolayer are plated sequentially. Instantaneous soldering with lead-free solder is realized under ultrasonic assistance at room temperature. This solves the residual stress and thermal damage caused by high melting point lead-free solder on thin chips and thermal components, and ensures the safety and reliability of electronic components. Copper-based microstructures are deposited by electrochemical methods. An amorphous Ni-W alloy layer with a thickness of 180 nm is deposited on the Cu-based microstructures by adjusting the atomic ratio of the plating solution. The Ni-W layer is further coated with a 50 nm Au layer to prevent oxidation. Solid-phase transient soldering is realized by combining the Au/Ni-W multilayer thin-film-modified Cu substructures with commercial solder (SAC305) for a holding time of 3 s at a soldering pressure of 10,000 gf (20 MPa) while ultrasonically assisted. The soldered samples are aged at 180 °C for 10 min, 30 min, and 60 min, respectively. Copper substructures with different surface modifications are subjected to destructive shear experiments with solder balls. Scanning electron microscope and X-ray fluorescence thickness gauge are used to study the microstructure, intermetallic compound (IMC) composition thickness and properties of the soldered interface and section. The cone height of the Cu-based structure is 2-4 μm, and the diameter of the bottom is 800 nm-1200 nm, which has a sharp tip and an excellent L/D ratio. The interface between the Au/Ni-W modified Cu substructure and the solder ball is almost free of holes. The average shear strength at the soldering interface is about 43.06 MPa. The fracture surface after the shear experiment basically occurs inside the solder ball matrix, which belongs to the pure toughness fracture. The interface between the Au/Ni-W-modified Cu-based structure and the solder ball is subjected to long aging treatment at 180 °C. The soldering interface showed a "bright layer". New phases are generated on the solder side above the "bright layer", while no new phases appear on the Cu substructure side below the "bright layer". The copper-based microstructure is inserted into the inside of the solder ball to form an inlay and produce mechanical interlocking. Au/Ni-W alloy modification layer can effectively improve the surface hardness of copper-based structures. This creates a large hardness difference with soft solder and enables the formation of fewer holes in the insertion solder. Amorphous Ni-W alloys are prone to form dense oxide films during ultrasonication. The Au film modification prevents oxide generation and increases the average shear strength of the soldering interface. The Ni-W alloy layer retards the interdiffusion between Cu-Sn, blocks the excessive growth of Cu-Sn IMCs, and reduces the reliability problems caused by interface failure.

Ultrasonic-assisted connection of Cu/Cu structure using Sn58Bi solder enhanced by B4C nanoparticles

Application of Ultrasonic Power in Forming Sn58Bi/Cu Solder Joints with Trace Si3N4 Nanowire Doping

Ni mesh-reinforced ultrasonic-assisted Cu/Sn58Bi/Cu joint performance: Experiments and first-principles calculations

Microstructure evolution and grain refinement of ultrasonic-assisted soldering joint by using Ni foam reinforced Sn composite solder

Microstructure and Mechanical Properties of Ultrasonically Assisted Brazing of Dissimilar Cu–Al Alloys

Intermetallic compound evolution and mechanical properties of Cu/Sn58Bi/Cu 3D structures blended with B 4 C nanoparticles during isothermal aging

Tuning the microstructure and enhancing the mechanical properties of Au-20Sn/Au/Ni(P)/Kovar joint by ultrasonic-assisted soldering method

Microstructure and mechanical properties of Cu joints soldered with a Sn-based composite solder, reinforced by metal foam

Solid-phase transient soldering method based on Au/Ni-W multilayer thin-film-modified copper-based structures

Interfacial reaction and mechanical properties of Sn–Bi Cu core solder joints

Acoustic cavitation-induced microstructure evolution in ultrasonically brazed Al/Cu joints using Zn-Al alloy fillers

Ultrasonic-Assisted Semi-Solid Forming Method and Microstructure Evolution of Aluminum/Copper Brazed Joints

Study on the dual inhibition behavior of interfacial IMCs in Cu/SAC105/Cu joint by adopting SiC nanowires and nanocrystalline Cu substrate

Effect of the addition of CeO 2 nanoparticles on the microstructure and shear properties of Sn-57Bi-1Ag solder alloy

Avoiding degradation and increasing joint strength of Al alloys by rapid ultrasonic soldering at low temperature

Influence of doping Si 3 N 4 nanoparticles on the properties and microstructure of Sn58Bi solder for connecting Cu substrate

Improved microstructure and strength of Sn-Ag-Cu/Cu solder joint with Mo nanoparticles addition

Improve mechanical properties and corrosion resistance of Al/Sn heterogeneous joints by ultrasonic-assisted liquid phase diffusion bonding

Pulse electric current induced interfacial ductile phase on improving the mechanical properties of the Au20Sn/Cu solder joints

Microstructural evolution of joints with and without Sb, Ni in Sn58Bi solder under electro-thermal-force coupling

Accelerated solid-liquid interdiffusion bonding of Cu joint using a Cu10Ni alloy mesh reinforced SAC305 composite solder