Abstract:Nano-materials are increasingly being used as modified binder for improve the performance of cementitious materials. In this paper, nano-SiO2 and nano-Al2O3 were incorporated into the geopolymers formed by the mixture of construction solid waste (recycled concrete fine powder) and industrial solid waste (slag). The effects of the type and content of nanomaterials on the early reaction kinetics, physical and mechanical properties and microstructure of geopolymer composites were explored. Results show that the addition of nanomaterials mainly affected the dissolution stage of geopolymerization, played a nucleation effect and improved the reaction rate. The promotion effect of nano-Al2O3 was slightly greater than that of nano-SiO2. Based on the results of JMAK model, the formation of geopolymers composites was an one-dimensional heterogeneous nucleation control reaction, which followed a plate-like structure thickening mechanism. The addition of nanomaterials shortened the setting time. The incorporation of nano-Al2O3 was beneficial to improve the fluidity of geopolymer. Furthermore, the addition of the two nanomaterials could improve the compressive strength of geopolymers. The compressive strength tended to first increase and then decrease with increasing nano-SiO2 or nano-Al2O3 content. The optimal mixing ratio of nano-silica and nano-alumina were 1.2% and 1.6% respectively, and the 28-day compressive strengths were both 59.05 MPa, which were 23.35% higher than that without nano-materials. XRD and SEM-EDS analysis indicate that the incorporation of nanomaterials had no impact on the type of final products, but increased their number, particularly calcium-based gel products. The internal structure of geopolymer with nanomaterials was more dense and uniform than that without nanomaterials. The MIP observed that the addition of the two nano-materials reduced the porosity in the matrix, the number of macropores and the pore fractal dimension. The pore fractal dimension of geopolymer was negatively correlated with the compressive strength.

Characterization and Performance Evaluation of Geopolymer Prepared with Thermal-Mechanical Activated Aluminum Sulfate Residue

Thermal Stability of Geopolymer Modified by Different Silicon Source Materials Prepared from Solid Wastes

Experimental investigation on the mechanical performance and microscopic characterization of desulfurization gypsum-reinforced ternary geopolymer

Impacts of Alkaline Washing Pretreatment on Municipal Solid Waste Incineration Fly Ash (MSWI FA) and Resulting Geopolymers

Effects of Spodumene Flotation Tailings on Mechanical Properties of Acid-Based Geopolymer Mortar

Performance Optimization of FA-GGBS Geopolymer Based on Response Surface Methodology

Synthesis and Characterization of Geopolymer Prepared from Circulating Fluidized Bed-Derived Fly Ash

Mechanical and Microstructure Characterizations of Geopolymer Mortars Using Industrial Waste Materials

Effect of Activator Concentration on the Properties of Metakaolin-Based Geopolymer

Performances and Mechanism of Geopolymers Prepared from Thermally-treated Sludge and High-calcium Fly Ash

Preparation of One-Part Geopolymer Based on Thermally Activated Soda Residue

A sludge and modified rice husk ash-based geopolymer: synthesis and characterization analysis

Preparation and curing method of red mud-calcium carbide slag synergistically activated fly ash-ground granulated blast furnace slag based eco-friendly geopolymer

Influence of the Activator Concentration and Solid/Liquid Ratio on the Strength and Shrinkage Characteristics of Alkali-Activated Slag Geopolymer Pastes

Reaction kinetics, mechanical properties, and microstructure of nano-modified recycled concrete fine powder/slag based geopolymers

Study on Modification of Geopolymer Based on Recycled Concrete Fine Powder

Eco-sustainable Design of Seawater Sea-Sand Slag-Based Geopolymer Mortars Incorporating Ternary Solid Waste

Synthesis and Characterization of Geopolymer from Bayer Red Mud with Thermal Pretreatment

Alkali-hydrothermal activation of mine tailings to prepare one-part geopolymer: Activation mechanism, workability, strength, and hydration reaction

Preparation and properties of metakaolin-fumed-silica geopolymer modified with sodium silicate and potassium silicate activators

Assessing the Viability of a High Performance One-Part Geopolymer Made from Fly Ash and GGBS at Ambient Temperature