Abstract:The surface preparation is a prerequisite for ensuring the required properties of a diamond film formed by gas-phase deposition. The influence of the temperature and concentration of the CuSO 4 etchant on the structural and phase compositions of the surface of hard-alloy materials is considered in this work, and the structural and phase compositions of a continuous polycrystalline diamond film at its growth stages is also considered. The adhesion of the diamond films to the surface of hard-alloy materials is determined qualitatively. It is established that the treatment of the hard-alloy surface in the CuSO 4 solution at t = 23°C leads to the inhomogeneous removal of a cobalt binder with chipping WC grains and the formation of the porous structure in the surface layer of the WC–6% Co alloy. The treatment by the CuSO 4 etchant at t = –2°C provides the homogeneous etching of the Co binder over the boundaries of WC grains and the formation of a chemically homogeneous surface. The orientation growth and adhesion of the diamond film depend on the elemental composition of the WC–Co alloy surface after treatment by the CuSO 4 solution. If the treatment was performed at t sln = 23°C, then the removal of copper from the defect surface WC layer is complicated during the synthesis, which provides the multidirectional growth of diamond crystals in the film along two directions, 〈111〉 and 〈110〉, which causes critical biaxial compressive stresses (2.5 GPa) and leads to low film adhesion to the hard alloy surface. If the treatment is performed at t sln = –2°C, then the orientational growth of diamond crystals in the film occurs in one preferential crystallographic direction 〈111〉, which lowers the biaxial compressive stresses (1.7 GPa) and increases the adhesive bond of the film to the hard alloy surface. The structure imperfection calculated from the ratio of the lines of integrated intensities I 1333 / I 1580 using the Raman spectroscopy method decreases with an increase in concentration at negative temperatures and increases at positive temperatures of the CuSO 4 solution during surface preparation.

Achieving CVD diamond films on Mo0.5(TiZrTaW)0.5 highly concentrated alloy for ultrastrong corrosion resistance

Corrosion resistance of diamond films with different grain sizes

Microwave plasma CVD of diamond films on high concentration alloys: Microstructure, hardness and wear properties

Design of amorphous-nanocrystalline films of TiAlCrNbZr x multi-component alloy: The effect of Zr on the corrosion resistance and mechanical properties

Significant enhancement of the corrosion performance of Ti-6Al-3Nb-2Zr-1Mo alloy via carbon addition in reducing acid environment

Synthesis and Corrosion Resistance of High-Silica Zeolite MTW, BEA, and MFI Coatings on Steel and Aluminum

Effects of TiMoTa nano-crystalline interlayer on nucleation, adhesion and tribological behaviors of diamond coating

Tribological performance and corrosion behavior of aluminum alloy protected by Cr-doped diamond-like carbon thin film

Studies on Corrosion Behavior of a Single-Crystal Superalloy and Its Sputtered Nanocrystalline Coatings with Solid NaCl Deposit in O2 + 38 Vol.% H2O Environment at 700 °C

Excellent Corrosion and Wear Resistance of Amorphous and Crystalline ZrCoAl Alloys

A Novel Diamond-Like Carbon Film

Corrosion Properties of DLC Film in Weak Acid and Alkali Solutions

Corrosion and Tribocorrosion Performance of M (m=ta, Ti) Doped Amorphous Carbon Multilayers in Hank'S Solution

Additive manufacturing of tantalum-zirconium alloy coating for corrosion and wear application by laser directed energy deposition on Ti6Al4V

The Effect of Surface Treatment on the Corrosion Behavior of Pure Ta Sheet in an Equimolar NaCl-KCl Melt at 850℃ in Air, Part 2: Diamond Film, TaC Film, Ta-Si Coating and Ta-Si-Al Coating

The Corrosion Behavior of Ti-6Al-3Nb-2Zr-1Mo Alloy: Effects of HCl Concentration and Temperature

Role of TiC nanocrystalline and interface of TiC and amorphous carbon on corrosion mechanism of titanium doped diamond-like carbon films: Exploration by experimental and first principle calculation

Improved corrosion protection of CrN hard coating on steel sealed with TiOxNy-TiN composite layers

Growth Features of Diamond Films on the Tungsten Carbide Surface with a Copper Sublayer

Effect of Zirconium Content on the Microstructure and Corrosion Behavior of As-Cast Ti-Al-Nb-Zr-Mo Alloy

Insights into the Microstructure and Corrosion Behavior of In-Situ Synthesized TiC/Ti-6Al-3Nb-2Zr-1Mo Composites