Abstract:In order to improve the wear and corrosion resistance of Ti-6Al-4V, a novel beta-Ta2O5 nanoceramic coating was synthesised using reactive sputter deposition enabled by double glow discharge plasma technique. The surface topography, chemical composition, and microstructure of the newly developed coating were characterised by a variety of surface analytical techniques. The coating microstructure was found to exhibit a compact striated pattern extending in a direction perpendicular to coating surface, which is composed of equiaxed beta-Ta2O5 grains with an average grain size of similar to 20 nm, well adhered to the Ti-6A1-4V substrate. The hardness and the Young's modulus of the as-deposited coating were obtained by nanoindentation, and the adhesion strength between the coating and substrate was determined by a scratch tester. The dry sliding wear behaviours of the coating were investigated at room temperature against Si3N4 ceramic balls at room temperature under applied loads ranging from 2.3 N to 5.3 N using a ball-on-disc tribometer. The specific wear rates of the coating exhibited only a slight increase with applied normal load, and were shown to be two orders of magnitude lower than that for Ti-6Al-4V under the same loading condition. Furthermore, the electrochemical behaviour of the coating immersed in 3.5 wt.% NaCl solution was systematically examined by using a range of complementary electrochemical techniques including potentiodynamic polarisation, electrochemical impedance spectroscopy (EIS), MottSchottky analysis as well as potential of zero charge (PZC). The results showed that the corrosion resistance of the beta-Ta2O5 nanoceramic coating was better than that of Ti-6Al-4V alloy in 3.5 wt.% NaCl solution. Hence, by possessing higher mechanical properties and good wear and corrosion resistance, the beta-Ta2O5 nanoceramic coating is considered to be a promising candidate for protection of engineering components operating under harsh conditions. (C) 2016 Elsevier B.V. All rights reserved.

The Effect of Surface Treatment on the Corrosion Behavior of Pure Ta Sheet in an Equimolar NaCl-KCl Melt at 850℃ in Air, Part 2: Diamond Film, TaC Film, Ta-Si Coating and Ta-Si-Al Coating

The Effect of Surface Treatment on the Corrosion Behavior of a Pure Ta Sheet in an Equimolar NaCl–KCl Melt at 850°C in Air. Part 1: Laser Surface Melting

Plasma surface tantalum alloying on titanium and its corrosion behavior in sulfuric acid and hydrochloric acid

The effect of Ta alloyed state on the corrosion resistance of TC4 surface laser cladding high entropy alloy

Corrosion and Wear Behaviours of a Reactive-Sputter-deposited Ta2O5 Nanoceramic Coating

Synthesis and Corrosion Resistance of High-Silica Zeolite MTW, BEA, and MFI Coatings on Steel and Aluminum

Corrosion properties of β-Ta alloyed Ti6Al4V by double-glow plasma surface alloying technique

Self-adaption Ta/TaC multilayer coating with fine grains: toward excellent corrosion resistance in aggressive environment

Hot Corrosion and Electrochemical Behavior of NiCrAlY, NiCoCrAlY and NiCoCrAlYTa Coatings in Molten NaCl-Na2SO4 at 800 °C

Surface Characteristics and Corrosion Resistance Properties of TiNi Shape Memory Alloy Coated with Ta

A Study on the High-Temperature Molten Salt Corrosion Resistance of Hot-Dip Aluminum/Carburizing Composite Coating on Ti65 Titanium Alloy

A high-resolution characterization of surface film formed on alloys 800 and 690 exposed to chloride and thiosulfate-containing solution at 300°C

Study on the Influence of Surface Treatment Process on the Corrosion Resistance of Aluminum Alloy Profile Coating

Corrosion and Tribocorrosion Performance of M (m=ta, Ti) Doped Amorphous Carbon Multilayers in Hank'S Solution

Corrosion Properties of DLC Film in Weak Acid and Alkali Solutions

Reactive-sputter-deposited Β-Ta 2 O 5 and TaON Nanoceramic Coatings on Ti–6Al–4V Alloy Against Wear and Corrosion Damage

Corrosion and passivation behavior of in-situ TiC reinforced Al 0.1 CrNbSi 0.1 TaTiV refractory high entropy alloy coatings via doping C

Corrosion Behavior of SiO2-Al2O3 Glass Composite Coating on TC4 in Marine Environment

Oxidative Corrosion Mechanism of Ti2AlNb-Based Alloys during Alternate High Temperature-Salt Spray Exposure

Effect of magnetron sputtered Al coating and anodization on the hot corrosion performance of Ti48Al2Nb2Cr alloy

Corrosion behavior of cold sprayed 7075Al composite coating reinforced with TiB2 nanoparticles