Abstract:Despite recent advances and improvements in modeling and prediction of the dynamics of the machining process, an efficient machining process is limited due to chatter and instability of machining system. In fact, the machining system contains various kinds of joints, which cause difficulties in dynamics modeling, simulation and prediction. Moreover, the flexible support system results in large deformation and violent vibration of the workpiece when machining, and the thin-walled workpiece easily gives rise to the chatter of the machining system. Therefore, the dynamics of the flexible support system was considered to calculate stability lobe diagram in the modeling of milling process. The whole machining system was regarded as a closed loop composed by the machine tool structures, support, workpiece and machining process. In this paper, the receptance coupling (RC) method was introduced to predict the dynamics of the closed machining system. A milling process was taken for example to predict the chatter limitations using the dynamics of closed model. The mathematical model of the machining system (machine tool structures, spindle, holder and tool), together with the details of joint contacts, was given based on the RC method. The RC model was used to obtain the dynamics of the system, while receptance of the tool point was coupled. Based on the coupling model of the machining system, the depth limitations under different speeds were estimated for the technology parameter optimization in milling process. The response was considered to be the sum of the cutting point and the support system. The flexibility of the support system was considered to be the feedback of the cutting stiffness. By this means, the traditional model was modified to calculate the stability lobe diagram based on the dynamics of the spindle and support system. Furthermore, the milling experiment was carried out to verify the prediction results, and the dominant natural frequencies of receptance at tool point were obtained by modal testing to define the stability lobe diagram. It was found that the chatter results matched well with the stability lobes. It was concluded that the support system with poor stiffness might cause violent chatter especially when the workpiece was thin-walled. The cutting depth limitations of the flexible support system were lower than that of the rigid one. Moreover, this closed model of the machining system is appropriate for the chatter prediction of the flexible support system or thin-walled workpiece, so it is helpful for a better parameter optimization.

Prediction of Chatter Stability in Bull-Nose End Milling of Thin-Walled Cylindrical Parts Using Layered Cutting Force Coefficients

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

Modeling of Non-Linear Cutting Forces for Dry Orbital Drilling Process Based on Undeformed Chip Geometry

Chatter Stability Prediction of Ball-End Milling Considering Multi-Mode Regenerations

Stability Prediction of Milling Process with Closed Machining System Dynamics with Flexible Thin-Walled Workpiece

Prediction of Chatter Considering the Effect of Axial Cutting Depth on Cutting Force Coefficients in End Milling

Dynamic Modeling for Chatter Analysis in Micro-Milling by Integrating Effects of Centrifugal Force, Gyroscopic Moment, and Tool Runout

Stability analysis of thin-walled parts end milling considering cutting depth regeneration effect

Milling Stability Prediction for Flexible Workpiece Using Dynamics of Coupled Machining System

Robust Chatter Stability Prediction of the Milling Process considering Uncertain Machining Positions

Chatter suppression analysis for variable pitch cutter in milling

Stability Analysis of Milling Based on the Barycentric Rational Interpolation Differential Quadrature Method

Active Control of Milling Chatter Based on the Built-in Force Actuator

Modeling of variable-pitch/helix milling system considering axially varying dynamics with cutter runout offset and tilt effects

Chatter stability analysis of variable speed milling with helix angled cutters

Chatter prediction in flank milling of thin-walled parts considering force-induced deformation

Modal parameter identification of general cutter based on milling stability theory

Prediction of time-varying dynamics and chatter stability analysis for surface milling of thin-walled curved CFRP workpiece

Digital Modeling-Driven Chatter Suppression for Thin-Walled Part Manufacturing

An efficient and precise stability analysis method for milling process

Modelling of the stability of variable helix end mills