Abstract:2.5D advanced packaging technology is a promising solution for “more than Moore”. TGV interposer has attracted growing attention for the high-frequency applications in 2.5D advanced packaging due to its low dielectric constant and loss tangent, etc. Some typical failure modes of TGV structure were discussed in the previous literatures. However, there is a lack of systematic research on the failure mechanisms of TGV under annealing and thermal shock condition. This paper focused on the failure mechanisms of TGV under different thermal conditions using both experimental and simulation methods. Annealing experiment was carried on the TGV sample at 400 °C for different periods. Crack appeared in the glass at the top corner of TGV after annealed at 400 °C for 5 min. With the increasing annealing period from 5 min to 30 min at 400 °C, the protrusion height of TGV increased from $0.61\ \mu\mathrm{m}$ to $1.21\ \mu \mathrm{m}$ , and the simulated protrusion height increased from $0.50\ \mu \mathrm{m}$ to $0.89\ \mu \mathrm{m}$ . The FEA simulation result showed that stress concentration was located in the top corner of TGV, the stress was 1456.63 MPa at 400 °C for 5 min. TGV samples were subjected to 0, 300, 500 and 1000 cycles under the condition of $-55\ ^{\circ}\mathrm{C}$ to 150 °C. Glass will crack around TGV-RDL after 300 thermal shock cycles. The stress was found concentrated around TGV-RDL according to FEA, which was 370.34 MPa. Crack appeared at the bottom corner of the TGV after 1000 cycles. The equivalent plastic strain at the bottom corner of TGV increased from 1.09 to 3.64 with the cycles increased from 300 to 1000. This article analyzes failure mechanisms of TGV and provides design guidelines for the pretreatment process of TGV. The simulation result offers information for the reliability evaluation of TGV.

Study of Glass Metallization and Adhesion Evaluation for TGV Application

Study of the thermo-mechanical behavior of glass interposer for flip chip packaging applications

Process Development of A New Tgv Interposer for Wafer Level Package of Inertial Mems Device

Directly Electroplated Metallization on Through Glass Via (TGV) Using Silver Nanowires Conductive Composite as Seed Layer

Processing Through Glass Via (TGV) Interposers for Advanced Packaging

Cu metallisation on glass substrate with through glass via using wet plating process

Modeling and Characterization of Annealing Effect on the Cu Protrusion and Thermomechanically Behaviors of Through Glass Via

Modeling and Characterization of Annealing Effect on the Cu Protrusion and Thermo-mechanically Behaviors of Through Glass Via

Selective metallization of glass with improved adhesive layer and optional hydrophobic surface

Low-Temperature Bonding And Interfacial Failure Behavior Of Si/Glass And Glass/Glass Chips

Performance and reliability study of TGV interposer in 3D integration

Study of Interfacial Adhesion and Re-Ir Alloy Coating in Chalcogenide Glass Molding.

Characterization of a Semiconductor Packaging System utilizing Through Glass Via (TGV) Technology

Effects of interface thermal resistance on surface morphology evolution in precision glass molding for microlens array.

Wear of mold surfaces: Interfacial adhesion in precision glass molding

Study on α-Al2O3 anti-adhesion coating for molds in precision glass molding

Failure Mechanisms Investigation of Through Glass Via (TGV) under Thermal Annealing and Shock

Recent Progress of TGV Technology for High Performance Semiconductor Packaging

Thermo-Mechanical Reliability Study of Through Glass Vias in 3D Interconnection

Glass-Based Micro-Hotplate with Low Power Consumption and TGV Structure Through Anodic Bonding and Glass Thermal Reflow

A comprehensive numerical analysis for preventing cracks in 2.5D glass interposer