Abstract:Laser machining has been emerging as a powerful alternative for cutting thin metal substrates. In this study, the application of pulsed laser cutting of a thin nonoriented silicon steel, with a thickness of 0.1 mm, was studied. The four processing parameters considered were laser power, cutting speed, pulse repetition rate, and processing environment. The two outputs to be measured were the extent of heat-affected zone (HAZ) and deviation of magnetic flux density (MFD) from initial value. Each input was designed with three levels and the three processing environments were air, deionized water, and sodium chloride solution. Based on the experimental design of the L27 Taguchi method, 27 parameter sets out of the total of 81 sets were used for the experiment. Results show that HAZ and MFD were negatively correlated. Compared with processing in air, cutting in the liquid could effectively reduce the HAZ. In the 27 experimental cases, the achieved minimum HAZ was 34.5 μm that corresponded to retaining 99% of initial MFD. The importance of the input was analyzed by the random forest method. The most and second significant parameters were laser power and environmental condition and their importance levels were 50.82% and 40.99%, respectively. Four artificial intelligence (AI) prediction models, full quadratic multiple regression analysis, artificial neural network, random forest, and extreme learning machine (ELM), were established based on randomly selecting 80% of the 27 data sets for training and the remaining 20% for testing. Model verification was executed by arbitrarily taking 10 additional new predictive parameter sets, from the remaining 54 parameter sets, for experiments. After comparing the predicting and experimental results, ELM model was found to have the best forecast performance. Thus, it was chosen as the target model for output optimization by the genetic algorithm method (GA). Through implementing the predicted optimal processing parameters from the resulting ELM-GA algorithm for the confirmation experiment, the obtained MFD and HAZ were 1.639 T and 30.41 μm, respectively, which were very close to that of the predicted optimal outputs, 1.640 T for MFD and 29.90 μm for HAZ.

Multi-Objective Optimization of High-Power Fiber Laser Cutting of Thick Mild Steel by Using Response Surface Methodology

Hybrid modeling and optimization of fiber laser hole cutting of austenitic stainless-steel sheets using response surface

Predicting and Enhancing the Multiple Output Qualities in Curved Laser Cutting of Thin Electrical Steel Sheets Using an Artificial Intelligence Approach

Feasibility analysis and cutting process research on laser cutting medium-thick 20CrNiMo steel plates using a high-power fiber laser without assisted blowing

A comprehensive review of studying the influence of laser cutting parameters on surface and kerf quality of metals

Multi-objective optimization of fiber laser cutting quality characteristics of glass fiber reinforced plastic (GFRP) materials

Multi-objective Numerical Simulation of Geometrical Characteristics of Laser Cladding of Cobalt-Based Alloy Based on Response Surface Methodology

Evaluation and Optimal Design of Supersonic Nozzle for Laser-Assisted Oxygen Cutting of Thick Steel Sections

Experimental Modeling, Statistical Analysis, and Optimization of the Laser-Cutting Process of Hardox 400 Steel

Effect of Fiber-Laser Parameters on Cutting Accuracy of Thin and Thick S355JR Structural Steel Plates

Artificial intelligence-based modeling and optimization of heat-affected zone and magnetic property in pulsed laser cutting of thin nonoriented silicon steel

Multi-objective Optimization of Kerf-taper and Surface-roughness Quality Characteristics for Cutting-operation On Coir and Carbon Fibre Reinforced Epoxy Hybrid Polymeric Composites During CO2-Pulsed Laser-cutting Using RSM

Multiobjective optimization of laser welding parameters for P92 steel based on MFO/MOEAD-Kriging

Multiobjective Optimization of Laser Polishing of Additively Manufactured Ti-6Al-4V Parts for Minimum Surface Roughness and Heat-Affected Zone

Optimization of tungsten carbide processing parameters for laser heating and ultrasonic vibration composite assisted cutting

A combined approach of artificial neural network, multi-objective genetic algorithm, and response surface methodology for enhanced PMMA micro-channeling in low power fiber laser beam machining

Optimization of heat affected zone in laser cutting of Kevlar-29 fiber composite using hybrid response surface based grey wolf optimization (RSGWO) algorithm

Response surface methodology-based optimization of parameters and cutting quality of 22MnB5 plates by UV picosecond laser layered cutting

A study on the cutting efficiency of gas-laser hybrid cutting according to the optimal cutting speed when cutting 100 mm ultra-thick plates

Use of a diffractive optic for high power laser cutting

Optimization Method of Sheet Metal Laser Cutting Process Parameters under Heat Influence