Optimization Method of Sheet Metal Laser Cutting Process Parameters under Heat Influence

Yeda Wang,Xiaoping Liao,Juan Lu,Junyan Ma
DOI: https://doi.org/10.3390/machines12030206
IF: 2.899
2024-03-21
Machines
Abstract:To address the issues of workpiece distortion and excessive material melting caused by heat accumulation during laser cutting of thin-walled sheet metal components, this paper proposes a segmented optimization method for process parameters in sheet metal laser cutting considering thermal effects. The method focuses on predetermined perforation points and machining paths. Firstly, an innovative temperature prediction model Tp(r,t) is established for the nth perforation point during the cutting process, with a prediction error of less than 10%. Secondly, using the PSO-BP-constructed prediction model for laser cutting quality features and an empirical model for processing efficiency features, a multi-objective model for quality and efficiency is generated. The NSGA II algorithm is employed to solve the objective optimization model and obtain the Pareto front. Next, based on the predicted temperature at the perforation point using the model Tp(r,t), the TOPSIS decision-making method is applied. Different weights for quality and efficiency are set during the cutting stages where the temperature is below the lower threshold and above the upper threshold. Various combinations of machining parameters are selected, and by switching the parameters during the cutting process, the thermal accumulation (i.e., temperature) during processing is controlled within a given range. Finally, the effectiveness of the proposed approach is verified through actual machining experiments.
engineering, mechanical, electrical & electronic
What problem does this paper attempt to address?
This paper attempts to solve the problems of workpiece deformation and excessive material melting due to heat accumulation during the laser cutting of thin - walled metal sheets. Specifically, the paper proposes a segmented optimization method for thin - plate laser cutting process parameters based on thermal effects, aiming to improve the cutting quality and efficiency by controlling the temperature during the processing. The following is an overview of the main content of the paper: 1. **Research Background**: - Laser cutting is widely used in thin - plate metal processing because of its high precision and high efficiency. However, the thermal effects during the cutting process can cause workpiece deformation and excessive material melting, affecting the processing quality. - Existing research mainly focuses on optimizing the cutting path to reduce heat accumulation, but these methods sacrifice processing efficiency while improving quality. 2. **Research Objectives**: - Propose a segmented optimization method to control heat accumulation by adjusting processing parameters, thereby improving processing efficiency while ensuring cutting quality. - Establish an innovative temperature prediction model \(T_p(r, t)\) to predict the temperature of the n - th perforation point with an error of less than 10%. - Use the prediction model constructed by PSO - BP and the empirical model to generate a multi - objective optimization model, and solve the Pareto front by the NSGA II algorithm. - Based on the predicted temperature \(T_p(r, t)\) and the TOPSIS decision - making method, set the quality and efficiency weights at different stages, and select an appropriate combination of processing parameters to ensure that the temperature during the processing is controlled within a given range. 3. **Research Methods**: - **Establishment of Heat Transfer Model**: Establish heat transfer models \(T_n(r, t)\) and \(T_{Cn}(r, t)\) for perforation points and contour feature points, and obtain the total temperature \(T_p(r, t)=T_n(r, t)+T_{Cn}(r, t)\) of perforation point n by superimposing the temperatures of feature points. - **Experimental Design**: Design a three - factor and six - level orthogonal experiment to measure the temperature, processing quality, and processing time under different processing parameters. - **Model Optimization**: Use the PSO - BP algorithm to construct a neural network, generate the relationship curves between processing parameters and processing quality and efficiency, and use the NSGA II algorithm for multi - objective optimization. - **Decision - making and Verification**: Predict heat accumulation under different processing parameters based on the heat transfer model, use the TOPSIS method to obtain decision - making schemes that meet different objectives, ensure that the thermal influence of each processing part is within the temperature range, and finally verify the results through heat maps and experiments. 4. **Research Contributions**: - Propose an innovative segmented optimization method that can improve processing efficiency while ensuring cutting quality. - Establish an accurate temperature prediction model with an error of less than 10%, which helps to better control heat accumulation during the processing. - Provide a systematic method to select the optimal combination of processing parameters through multi - objective optimization and the TOPSIS decision - making method. Through the above methods, this research provides new ideas and solutions for solving the heat accumulation problem during the laser cutting of thin - walled metal sheets.