Abstract:The tension-compression yield asymmetry caused by the strengthening of Mg-Zn-Gd-Zr alloy due to extrusion deformation is an important issue that must be addressed in its application. In this study, the effects of loading direction on the tensile and compressive mechanical behaviors of Mg-5Zn-2Gd-0.2Zr alloy were systematically investigated. As the loading angle (the angle between the loading direction and the extrusion direction) increases from 0° to 30°, 45°, 60° and 90°, the tensile yield strength decreases more significantly than the compressive yield strength. Consequently, the tension-compression yield asymmetry is gradually improved. Additionally, the ultimate compressive strength decreases more markedly than the ultimate tensile strength with the increment of the loading angle. In tensile tests conducted at 0°, 30° and 45°, two distinct stages of decreasing strain hardening rates are typically observed. For the 60° and 90° tensile tests, one unusual ascending stage of strain hardening rate is observed. For all compressive tests, three stages of strain hardening are consistently noted; however, the increment in strain hardening rate caused by {10–12} extension twinning decreases with the increasing loading angle. A model combining loading angle and Schmid factor distribution was established. The calculated results indicate that the dominant deformation modes during the yielding process also vary significantly with the loading conditions. This clarification highlights the differences in yield strength variations between tension and compression. Finally, an analysis of the plane trace and crack propagation direction near the fracture surface reveals the fracture mechanisms associated with tensile and compressive tests at different loading directions. This study promotes understanding of the mechanical behaviors of Mg-5Zn-2Gd-0.2Zr alloy under different loading directions, and helps to thoroughly elucidate the anisotropic effects of texture on the mechanical properties of magnesium alloys.

Deformation Mechanisms of Dual-Textured Mg-6.5Zn Alloy with Limited Tension-Compression Yield Asymmetry

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

Asymmetric Tension-Compression Mechanical Behaviors of Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy with Double-Peak Fiber Texture

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

The microstructure evolution and abnormal yield asymmetry of extruded Mg-10Gd-0.5Zr alloy

The Role of Bimodal-Grained Structure in Strengthening Tensile Strength and Decreasing Yield Asymmetry of Mg-Gd-Zn-Zr Alloys

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Unique Deformation Mechanisms of Extruded Mg-Y-Sm-Zn-Zr Alloy

Reducing Yield Asymmetry in a Wrought Mg–9Al Alloy by Randomized Texture Achieved Via Multi-Directional Forging

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

Asymmetric Tension-Compression Mechanical Behavior of the As-Cast Mg-4.58Zn-2.6Gd-0.16Zr Alloy

Combined-extrusion techniques for fabricating yield-symmetric ZK61 magnesium alloys rods focusing on texture influence on their mechanical responses

Tension–Compression Yield Asymmetry Influenced by the Variable Deformation Modes in Gradient Structure Mg Alloys

Effect of Loading Direction on Tensile-Compressive Mechanical Behaviors of Mg-5Zn-2Gd-0.2Zr Alloy with Heterogeneous Grains

Abnormal Extrusion Texture and Reversed Yield Asymmetry in a Mg–Y-Sm-Zn-Zr Alloy

Improving the tension-compression asymmetry of ZK61 magnesium alloy through texture optimization in combined extrusion

Twinning and Mechanical Behavior of an Extruded Mg–6Al–3Sn Alloy with a Dual Basal Texture

Tension-compression Asymmetry of a Rolled Mg-Y-Nd Alloy

Processing and Properties of Mg–6Gd–1Zn–0.6Zr

Adjusting Approaches of Basal Texture for Improvement of Tension-Compression Asymmetry in Extruded Magnesium Alloys

Improved Tension/compression Asymmetry Achieved in High-Strength Magnesium Alloys Via Compression-Extrusion Process