Abstract:Microstructure, texture evolution and mechanical properties of extruded Mg-4.58Zn-2.6Gd-0.18Zr alloy were investigated at extrusion temperatures of 260 °C, 280 °C and 300 °C, extrusion ratios of 10, 15 and 30, and ram speeds of 3 mm s−1 and 6 mm s−1, respectively. The results indicated that the as-cast experimental alloy was composed of α-Mg matrix, coarse α-Mg + W(Mg3Zn3Gd2) eutectic and icosahedral quasicrystalline I(Mg3Zn6Gd) phase. A small amount of undissolved W phases were detected after the homogenization treatment at 505 °C up to 16 h, while most I phase dissolved into the α-Mg matrix. The initial crystallites before extrusion were randomly oriented, and showed a typical random texture. After extrusions, all samples exhibited a bimodal microstructure consisting of fine Dynamic recrystallization (DRX) grains and coarse elongated un-DRX grains, and the formation of ultra-fine DRX grains only occurred in the sample with an extrusion ratio of 10 at 260 °C, 3 mm s−1, which was caused by the solute segregation in homogenized billets and non-uniformly distributed W phase during the extrusion process. A fiber texture with {0002} planes and <1̄21̄0> directions paralleled to the extrusion direction was observed to be dominant in all the extruded samples. Furthermore, the increase of extrusion ratio was found to be beneficial for the DRX process and refinement of grain size, and the maximum texture intensity was accordingly weakened, which resulted in a decrease of tensile yield strength but an increase of elongation. With increasing the extrusion temperature or ram speed, both the grain size and DRX fraction gradually increased. Consequently, the texture was randomized and the maximum texture intensity decreased, which led to a reduction of the elongation and tensile yield strength. The tensile failure behaviors under different extrusion conditions were found to be related with the contraction twin lamellas formed in the un-DRX grains and the string-like W phases.

Unique Deformation Mechanisms of Extruded Mg-Y-Sm-Zn-Zr Alloy

Formation Mechanism of the Abnormal Texture During Extrusion in Mg-Y-Sm-Zn-Zr Alloy

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

Texture Evolution and Deformation Activity of an Extruded Magnesium Alloy: Effect of Yttrium and Deformation Temperature

Revealing the dynamic recrystallization mechanism, extrusion deformation mechanism, and tensile deformation behavior of Mg–6Al–1Zn–1.1Sc alloy

Plastic Strain Accommodation and Crack Initiation in a Randomly-Oriented Mg-8y-1zr Magnesium Alloy During Accumulated Tensile Deformation

The microstructure evolution and abnormal yield asymmetry of extruded Mg-10Gd-0.5Zr alloy

Analysis of Abnormal Texture and Strengthening Mechanisms of Extruded Mg–Gd–Y–Nd–Zr Alloy

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

Deformation Behavior and Texture Evolution in an Extruded Mg-Li Sheet with Non-Basal Texture During Tensile Deformation

Texture Weakening and Grain Refinement Behavior of the Extruded Mg-6.03Zn-0.55Zr Alloy During Hot Plane Strain Compression

Cooperative Achievement in Grain Refinement and Texture Weakening of Mg-Gd-Y-Sm-Zr Alloy Fabricated by Asymmetric Extrusion-Shear Process

Microstructure, Texture Evolution and Tensile Properties of Extruded Mg-4.58Zn-2.6Gd-0.16Zr Alloy

Abnormal Extrusion Texture and Reversed Yield Asymmetry in a Mg–Y-Sm-Zn-Zr Alloy

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Analysis of Abnormal Texture Formation and Strengthening Mechanism in an Extruded Mg-Gd-Y-Zn-Zr Alloy

Anisotropic cyclic deformation behavior of an extruded Mg-3Y alloy sheet with rare earth texture

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Deformation Mechanisms of As-Extruded Mg–3Bi–1Ca (wt.%) Alloy During Room-Temperature Tension

In-Situ Analysis of the Tensile Deformation Modes and Anisotropy of Extruded Mg-10gd-3y-0.5zr (wt.%) at Elevated Temperatures