Abstract:Titanium carbide (TiC) particulates-reinforced iron matrix composites were prepared by in situ fabrication method combining an infiltration casting with a subsequent heat treatment. The effects of different heat treatment times (0, 1,6 and 11 h) at 1138 degrees C on the phase evolution, microstructural features, and properties of the composites were investigated. The as-prepared composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and microhardness and wear resistance tests. The XRD results showed that the composites consisted of graphite, alpha-iron and titanium carbide after heat treatment at 1138 degrees C for 11 h. The SEM observation revealed that the formed TiC particulates were homogenously distributed in the iron matrix. The average microhardness of the composite heat treated at 1138 degrees C for 6 h increased depending upon the region: 209 HV0.1 (iron matrix) <787 HV0.1 (titanium wire) < 2667 HV0.1 (composite region). After being heat treated at 1138 degrees C for 11 h, the composite indicated no considerable change in microhardness value, and the average microhardness of the composite region was about 2354 HV0.1. The highest microhardness value obtained for the composite region was due to the formation of titanium carbide particulates as reinforcement phase within the iron matrix. Relative wear resistance was determined by a pin-on-disc wear test technique under different loads, and as a result, the composites containing higher volume fraction of hard titanium carbide particulates presented higher wear resistance compared with the unreinforced gray cast iron. (C) 2011 Elsevier Ltd. All rights reserved.

Preparation and Properties of in Situ Formed TiCx/high Chromium White Iron Composite with Honeycomb Structure

In situ (TiBw+TiCp)/Ti6Al4V composites with a network reinforcement distribution

Oxidation behavior of in situ TiCp/Ti6Al4V composite with self-assembled network microstructure fabricated by reaction hot pressing

In Situ Fabrication of Titanium Carbide Particulates-Reinforced Iron Matrix Composites

Preparation and Properties of ZTA + WC Particles/Hypereutectic High Chromium Cast Iron Composites

Oxidation behavior of high Cr white iron composites reinforced with TiC and nonstoichiometric TiC x in air at 600 °C

Preparation and Interface Structure of CTCp/Cr26 Composites with the Pinning Effect

Interface Structure and Wear Behavior of Cr26 Ferrous Matrix Surface Composites Reinforced with CTC P

On the Preparation and Wear Properties of Ceramic Particle-reinforced High-chromium Cast Iron-based Surface Composite Material

Microstructural Characterization of TiC-White Cast-Iron Composites Fabricated by In Situ Technique

Fabrication of Composites with Honeycomb-Shaped Ceramic Plates

Preparation and Interface Investigation of Fe/Al2o3p Composite Activated by Ni and Ti

Microstructure evolution, mechanical properties, and wear behavior of in-situ TiCx/TC4 composites

Preparation and Microstructural Characterization of a High-Cr White Cast Iron Reinforced with WC Particles

Interfacial bonding and wear behavior of macroscopic TiC particulates reinforced iron-based composites fabricated by infiltration casting process

In Situ Formation of Al3Ti and Its Effects on the Microstructure, Hardness and Tribological Properties of Al Matrix Composites with Various Ti Contents

Interface and wear characteristics of high-Cr cast iron matrix composite reinforced with cemented carbide particles

Preparation of ZrO 2-Al 2O 3 honeycomb ceramic reinforced high Cr cast iron matrix composites by composite processing

Microstructure, mechanical properties and strengthening mechanisms of in-situ prepared (Ti5Si3 + TiC0.67)/TC4 composites

Microstructure and Properties of TiCp/Fe Hierarchical Composites Prepared by a New Pressure Infiltration Method

Fabrication and interface property of WC-TiC-Co/Cr20 composites