Abstract:Eutectic high-entropy alloys (EHEAs) have been explored as possible options for hightemperature applications due to their controlled microstructure and excellent mechanical properties. In particular, EHEAs possess good liquidity and castability, allowing their possibility for real-size industrial manufacturing. However, despite their importance as a structural material index, the tribological properties were rarely investigated in the EHEAs field. In this study, a kilogram-scale AlCr1.3TiNi2 EHEA was produced using electromagnetic levitation melting and direct casting approach. The EHEA.. s microstructure and chemical composition were investigated using a TEM and APT techniques. The AlCr1.3TiNi2 EHEA's tribological properties were examined from room temperature to 800 degrees C using a rotational ball-on-disk tribometer (HT-1000). Meanwhile, for comparison, a GH4169 nickel-base superalloy was chosen. The corresponding wear mechanisms were also thoroughly discussed. The findings exhibit that the as-cast AlCr1.3TiNi2 EHEA, which had an ultrafine lamellar structure, consisted of a disordered bcc phase and an ordered L2(1) phase with lattice misfit of approximately 2%. The average interlamellar spacing was about 350 nm. Additionally, a large number of nanoprecipitates contains in the L2(1) lamellae central region. Below 600 degrees C, the AlCr1.3TiNi2 EHEA's primary wear mechanism was abrasive wear, and its wear rate was lower than that of the GH4169 alloy. At 800 degrees C, distinct plastic deformation features were observed on the worn surface of EHEA. The EHEA exhibited a much higher friction coefficient than that of the GH4169 alloy at 800 degrees C, but their wear rates were similar. The wear resistance improvement of GH4169 alloy at high temperature was ascribed to the formation of oxide film on its worn surface, and the AlCr1.3TiNi2 EHEA's excellent wear resistance mainly resulted from good structure stability and high hot hardness. Current findings offer new insights into the industrial application of EHEA in high-temperature fields.

High Temperature Tribological Performance of a Cost-Effective Eutectic High Entropy Alloy Al0.8CrFeNi2.2: Comparison with AlCoCrFeNi2.1

Mechanical Properties and Tribological Behavior of Al0.5CoCrFeNb0.5Ni High-Entropy Alloy at High Temperatures

Microstructure, Mechanical Properties and High-Temperature Sliding Wear Response of a New Al0.5CrFeNiV0.5 High-Entropy Alloy

Effects of temperature and microstructure on the triblogical properties of CoCrFeNiNbx eutectic high entropy alloys

Tribological Properties and Wear Mechanism of AlCr1.3TiNi2 Eutectic High-Entropy Alloy at Elevated Temperature

Tribological behavior of an AlCoCrFeNi2.1 eutectic high entropy alloy sliding against different counterfaces

Excellent Tribological Performance at Elevated Temperatures and Associated Mechanisms of Novel AlCoCrFeNi-MoS2 Solid Self-Lubricating Composite

Tribological performance of a cost-effective CrFeNiAl0.3Ti0.3 high entropy alloy based self-lubricating composite in a wide temperature range

High-temperature tribological behavior of CoCrFeNiV high-entropy alloys: A parallel comparison with CoCrFeNiMn high-entropy alloys

Mechanical, materials, and physicochemical effects on the high-temperature tribological behaviour of laser additive manufacturing AlCoCrFeNi2.1 eutectic high-entropy alloys

High-temperature Oxidation Behavior of AlCoCrFeNi2.1 Eutectic High-Entropy Alloy: Microstructure Evolution and Microhardness

Mechanical and Tribological Performance of CoCrNiHfx Eutectic Medium-Entropy Alloys

A comparative study of two C-containing high-entropy alloys Al0.3CrFeNi2 and Al0.3CoCrFeNi

Comparative Study of Mechanical and Corrosion Behaviors of Cost-Effective AlCrFeNi High Entropy Alloys

High-Temperature Tribological Behavior of Al0.3Cr0.5Fe1.5Mn0.5Ni High-Entropy Alloys With Addition of Titanium and Carbon

Mechanical and Tribological Performance of AlCr0.5NbTaxTi4-x ( X=0, 0.5, 1) Refractory High-Entropy Alloys

Microstructure and mechanical properties variation with Ni content in Al0.8CoCr0.6Fe0.7Nix (x = 1.1, 1.5, 1.8, 2.0) eutectic high-entropy alloy system

Effect Of Ti Addition On The Microstructure And Wear Properties Of Alfecrcocu High-Entropy Alloy

Room and Elevated Temperature Sliding Friction and Wear Behavior of Al0.3CoFeCrNi and Al0.3CuFeCrNi2 High Entropy Alloys

On Microstructure and Mechanical Performance of AlCoCrFeMo0.5Nix High-Entropy Alloys

Microstructure, Hardness, Wear Resistance, and Corrosion Resistance of As-Cast and Laser-Deposited FeCoNiCrAl0.8Cu0.5Si0.5 High Entropy Alloy