Abstract:This paper presented an innovative three-dimensional vibration isolation bearing (3D-VIB) to mitigate horizontal seismic action and rail-induced vertical vibration. The 3D-VIB was composed of a thick laminated rubber bearing acting as the vertical vibration isolation module and a friction pendulum acting as the horizontal seismic isolation module. The thick laminated rubber bearing was used as a part of the slider in the friction pendulum. The compression performance of 3D-VIB was decoupled from its shear performance by concentrating the compressive deformation into the thick rubber bearing while shear deformation occurred independently in the friction pendulum module. The bearing capacity, vertical and horizontal properties of a full-scale 3D-VIB specimen were tested. In the test, the ultimate bearing capacity of 3D-VIB was 7 times that of the design compressive load of normal service condition. The vertical stiffness of the specimen under seismic vibration and vertical rail-induced vibration were tested separately. It was found that the vertical stiffness of the specimen under rail-induced vibration was 1.55 times higher than the vertical stiffness under seismic vibration. The horizontal performance of the 3D-VIB was characterized by stable parallelogram-shaped hysteretic curves similar to that of the traditional friction pendulum system. A user-defined element was developed and incorporated into ABAQUS to simulate the mechanical behavior of the 3D-VIB under different loading conditions, and simulation results agreed with the test results. The responses of a steel structure equipped with the 3D-VIB, while subjected to earthquake ground motions and rail-induced vibrations, respectively, were analyzed and compared with the non-isolated one. The analysis results suggested that with the installation of the 3D-VIB, the maximum inter-story drift ratio of the structure under maximum considered earthquake was reduced by about 88%. The average maximum transient vibration value of the rail-induced vertical vibration at the typical points of the conventional model was 86.2 dB, while that in the 3D-isolated model was 78.6 dB, the vibration reduction was 7.6 dB.

Research on vertical isolation performance of lattice shell canopy with three-dimensional FPB of Beijing Workers'Stadium

Design and Research of the Long-Span Truss String Structure for the Platform Canopy of Beijing North Station

Stability and Seismic Behavior Analysis of the Canopy Shell of Large Stadium

Seismic Performance Assessment of a Single-Layer Spherical Lattice Shell Structure with Multifunctional Friction Pendulum Bearings

Seismic Behaviors of High-Strength Bolted End-Plate Connected Composite Steel Beam and Square Concrete Filled Steel Tube Column Frames

Seismic protection of a single-layer spherical lattice shell structure using a separated three-dimensional isolation system

Evaluation of isolation performance of, reticulated shell structures with curvature-consistent frictional pendulum isolation system through shaking table tests

Shaking table tests on seismic behaviors of a single-layer spherical lattice shell with shape memory alloy-controlled friction pendulum bearings

Shaking table tests of base-isolated reinforced concrete frame by double friction pendulum bearings

Study on overall stability of steel canopy structure with open single-layer flat thin arch shell in Beijing Workers'Stadium

Shaking table tests and numerical studies on the seismic behaviors of FPB in railway continuous beam bridges

Study on Seismic Isolation of Long Span Double Deck Steel Truss Continuous Girder Bridge

Wind-Induced Dynamic Response of Inter-Story Isolated Tall Buildings with Friction Pendulum Bearing Based on an Enhanced Simplified Model

Shaking table test of a steel frame structure with layered three‐dimensional isolation

Development of an innovative three-dimensional vibration isolation bearing

Seismic performance improvement of a three-dimensional isolated spherical reticulated shell structure using pseudo-negative-stiffness magnetorheological dampers

Shaking table test of space double-layer cylindrical reticulated shell with three-dimensional isolation bearing

Study of the mechanics of progressive collapse of FPB isolated beam-pier substructures

Shaking table tests on the seismic response of truss structure with air spring‐FPS three‐dimensional isolation bearing

Advances and challenges in friction pendulum bearings for seismic isolation systems

Experimental research and numerical simulation of a large-span isolated structure considering multi-dimensional input effects