Abstract:Wet gas compression systems and multiphase pumps are enabling technologies for the deep sea oil and gas industry. This extreme environment determines both machine types have to handle mixtures with a gas in liquid volume fraction (GVF) varying over a wide range (0–1). The gas (or liquid) content affects the system pumping (or compression) efficiency and reliability, and places a penalty in leakage and rotordynamic performance in secondary flow components, namely seals. In 2015, tests were conducted with a short length smooth surface annular seal (L/D = 0.36, radial clearance = 0.127 mm) operating with an oil in air mixture whose liquid volume fraction (LVF) varied to 4%. The test results with a stationary journal show the dramatic effect of a few droplets of liquid on the production of large damping coefficients. This paper presents further measurements and predictions of leakage, drag power, and rotordynamic force coefficients conducted with the same test seal and a rotating journal. The seal is supplied with a mixture (air in ISO VG 10 oil), varying from a pure liquid to an inlet GVF = 0.9 (mostly gas), a typical range in multiphase pumps. For operation with a supply pressure (Ps) up to 3.5 bar(a), discharge pressure (Pa) = 1 bar(a), and various shaft speed (Ω) to 3.5 krpm (ΩR = 23.3 m/s), the flow is laminar with either a pure oil or a mixture. As the inlet GVF increases to 0.9 the mass flow rate and drag power decrease monotonically by 25% and 85% when compared to the pure liquid case, respectively. For operation with Ps = 2.5 bar(a) and Ω to 3.5 krpm, dynamic load tests with frequency 0 < ω < 110 Hz are conducted to procure rotordynamic force coefficients. A direct stiffness (K), an added mass (M), and a viscous damping coefficient (C) represent well the seal lubricated with a pure oil. For tests with a mixture (GVFmax = 0.9), the seal dynamic complex stiffness Re(H) increases with whirl frequency (ω); that is, Re(H) differs from (K−ω2M). Both the seal cross coupled stiffnesses (KXY and −KYX) and direct damping coefficients (CXX and CYY) decrease by approximately 75% as the inlet GVF increases to 0.9. The finding reveals that the frequency at which the effective damping coefficient (CXXeff = CXX − KXY/ω) changes from negative to positive (i.e., a crossover frequency) drops from 50% of the rotor speed (ω = 1/2 Ω) for a seal with pure oil to a lesser magnitude for operation with a mixture. Predictions for leakage and drag power based on a homogeneous bulk flow model match well the test data for operation with inlet GVF up to 0.9. Predicted force coefficients correlate well with the test data for mixtures with GVF up to 0.6. For a mixture with a larger GVF, the model under predicts the direct damping coefficients by as much as 40%. The tests also reveal the appearance of a self-excited seal motion with a low frequency; its amplitude and broad band frequency (centered at around ∼12 Hz) persist and increase as the gas content in the mixture increase. The test results show that an accurate quantification of wet seals dynamic force response is necessary for the design of robust subsea flow assurance systems.

Modeling of Lubricant Retention in Suction Lines with R32/PVE Oil Mixture Based on Different Flow Patterns

Solubility And Miscibility For The Mixture Of (Ethyl Fluoride Plus Polyol Ester Oil)

Experimental Analysis On Oil Film Properties Of Plane Port Pair In Axial Piston Machine

Experimental study of the lubricant-refrigerant flow in a rotary compressor

A mechanistic model for nucleate boiling heat transfer performance with lubricant-refrigerant mixture

Numerical investigation on performances of a CO2 ejector containing partially miscible lubricant using heterogeneous modeling

Experimental investigation and simulation on dynamic precipitation characteristics of R32-lubricating oil mixture in heat pump systems

Analysis and Comparison of the Models for the Rarefied Gas Effect on Gas Lubrication

Nucleate boiling heat transfer of R-134a and R-134a/POE lubricant mixtures on smooth tube

Experimental Measurement of Oil Droplets Size and Velocity Above the Rotor/Stator in a Rotary Compressor

A Mixed Lubrication Theoretical Model and Experimental Verification of Rotary Lip Seals

Investigation on the characteristics of oil supply system for a hermetic variable speed rotary compressor

150USRT Class R-513A Refrigerant Two-Stage Centrifugal Compressor Design Point and Separation Point Flow Field Simulation Analysis

Refrigerant migration and oil sump viscosity change of R290 high-pressure rotary compressor during shutdown process

Experimental investigation on flow patterns and pressure gradients of shale oil-water flow in a horizontal pipe

An Assessment of Friction Factor and Viscosity Correlations for Model Prediction of Refrigerant Flow in Capillary Tubes

Experimental Investigation on the Surface Tension of R1234ze(E)/POE Lubricant Mixtures from 278 K to 338 K

Leakage, Drag Power, and Rotordynamic Force Coefficients of an Air in Oil (Wet) Annular Seal

New Turbulent Lubrication Model in Hydrodynamic Face Seal

Numerical-experimental investigation of liquid slugging in the suction muffler of a hermetic reciprocating compressor

Experimental evaluation on flow boiling heat transfer of R290/POE-oil working fluid for absorption refrigeration in smooth horizontal tubes