Abstract:As the main gel material of concrete, cement is used in an astonishing amount every year in the construction industry. However, a large amount of CO 2 is emitted into the atmosphere while producing cement. Therefore, it is the general trend to look for substitutes for cement and develop new green concrete. Lithium slag (LS) is the industrial waste discharged from lithium salt plants. Through testing, it is found that the chemical composition of LS has a high degree of coincidence with ordinary Portland cement (OPC) Therefore, LS can be incorporated into concrete as supplementary cementations material (SCM) to prepare lithium slag concrete (LSC). The pollution of the natural environment caused by a large number of piled-up and landfilled LS is immeasurable. Consuming and using LS in large quantities and with high efficiency not only eliminates the pollution of lithium slag to the natural environment, but also helps to reduce the amount of cement used in green concrete and truly reuse waste resources. In order to study the mechanical properties of post-heated LSC, the test were carried out for LSC specimens after high-temperature. The main influence factors were considered, including the temperatures of 20°C, 100 °C, 300 °C, 500 °C and 700 °C, the contents of lithium slag in LSC of 0%, 10%, 20% and 30%, cooling method of LSC after exposure high temperature. The results showed that the mechanical properties of LS concrete specimens were slightly improved at 100 °C, and when the temperature was 300 °C or higher, the damage to the specimens was huge and irreversible. An appropriate amount of LS (20% lithium slag content) could improve the strength of LSC. This paper also studied the relationship between lithium slag content and strengths of LS concrete. The research results show that adding an appropriate amount of LS to concrete improves the mechanical properties of concrete. When the LS replacement rate is 20%, the mass loss rate of LSC after different high temperature treatments was the minimum. The cubic compressive strength, axial compressive strength, and flexural strength of specimens with 20% LS substitution can be increased by 8.16%, 8.33%, and 13.46% after high temperature. The cubic compressive strength, axial compressive strength, and flexural strength of specimens with 20% LS substitution can be increased by 8.16%, 8.33%, and 13.46% after high temperature.

Improving the Performance of Ultra-High Performance Concrete Containing Lithium Slag by Incorporating Limestone Powder

Incorporating Limestone Powder and Ground Granulated Blast Furnace Slag in Ultra-high Performance Concrete to Enhance Sustainability

The Synergistic Effects of Ultrafine Slag Powder and Limestone on the Rheology Behavior, Microstructure, and Fractal Features of Ultra-High Performance Concrete (UHPC)

Influence of limestone powder on water film thickness and plastic viscosity of UHPC

Evaluation of mechanical properties and environmental impact of using limestone powder in high performance concrete

A Review on Cementitious and Geopolymer Composites with Lithium Slag Incorporation

Research on the High Performance of Concrete Mixed with Lithium Slag in Hydraulic Structures

Mechanical properties and microstructure of ultra-high performance concrete with low cement content

Preparation for micro-lithium slag via wet grinding and its application as accelerator in Portland cement

Effect of Shale Powder on the Performance of Lightweight Ultra-High-Performance Concrete

Hydration kinetics and microstructure development of Ultra-High Performance Concrete (UHPC) by high volume of phosphorus slag powder

Performance optimization and hydration mechanism of a clinker-free ultra-high performance concrete with solid waste based binder and steel slag aggregate

Effect of high temperature on mechanical properties of lithium slag concrete

Utilization of sewage sludge ash in ultra-high performance concrete (UHPC): Microstructure and life-cycle assessment

Mechanical Properties and Shrinkage of Ultrahigh-Performance Concrete Containing Lithium Carbonate and Nano-Calcium Carbonate

Effect of High Content Limestone Powder on Microstructure and Mechanical Properties of Cement-based Materials

Influence of limestone powder mixing method on properties of manufactured sand concrete

Mechanical properties and hydration of ultra-high-performance seawater sea-sand concrete (UHPSSC) with limestone calcined clay cement (LC3)

Effects of Steel Slag Powder and Expansive Agent on the Properties of Ultra-High Performance Concrete (UHPC): Based on a Case Study

Preparation and properties of ultra-high performance concrete incorporation multi-mineral admixtures

Application of Copper Slag in Ultra-high Performance Concrete