Abstract:Abstract Additive manufacturing (AM) is a developing manufacturing technology, which provides excellent attributes compared to other manufacturing techniques. However, one of the critical challenges is the presence of defects that hinder the mechanical properties of the parts, particularly the fatigue life. Experimental understanding of fatigue is a cumbersome process. Therefore, numerical prediction based on specified conditions (such as porosity and applied load) can be an alternative to experimental analysis at the design stage of AM parts. In this study, elastic–plastic finite element analysis (FEA) is performed to obtain the stress distribution around pores, and their resultant effect on fatigue life for L-PBF (laser powder bed fusion) produced AlSi10Mg alloy samples. The stress field is calculated for both single and multiple pore models, where stress concentration is evaluated as a function of the pore’s location and its size. It is found that both pore location and size affect the stress field; however, location effects dominate over pore size. For the same remote applied stress level, the stress concentration around the pore increases with an increase in pore size, and the local maximum stress occurs near the pores that are closest to the surface. The current study also evaluates the relative effect of porosity fraction, average pore size, and location. It is found that the magnitude and sensitivity of stress concentration are hierarchically controlled by porosity location, pore size, and porosity density. A multi-scale finite element (FE) model is proposed based on inherent porosity data measured using Computed Tomography (CT) to predict overall fatigue life. The fatigue cycles are calculated using the rainflow counting algorithm in FE Safe using the stress–strain data obtained from the proposed FEA model. Using the proposed model, it is possible to generate S–N curves for any loading condition for a given porosity condition (porosity density and average pore size). The S–N curve results obtained from the FE model are compared to the experimental observations. The predicted fatigue life shows approximately 5% error with experimental results at high stress loading conditions. However, the proposed model overpredicts the fatigue life at low stress loading by almost 30%.

Prediction of High Cycle Fatigue Strength for Additive Manufactured Metals by Defects Incorporated Crystal Plasticity Modeling

Defect characteristics-based low-cycle fatigue life prediction model for additive manufactured Ti-6Al-4 V alloys

High Cycle Fatigue Life Prediction Model Based on Crystal Plasticity and Continuum Damage Mechanics for Ni-based Single Crystal Superalloys under a Multiaxial Stress State

The potency of defects on fatigue of additively manufactured metals

Critical physics informed fatigue life prediction of laser 3D printed AlSi10Mg alloys with mass internal defects

High-cycle and very-high-cycle fatigue lifetime prediction of additively manufactured AlSi10Mg via crystal plasticity finite element method

Low-cycle Fatigue Behavior and Life Prediction of TA15 Titanium Alloy by Crystal Plasticity-Based Modelling

Very-high-cycle fatigue behavior of AlSi10Mg manufactured by selected laser melting: Crystal plasticity modeling

A Multiscale High Cycle Fatigue Approach Based on Shakedown and Cohesive Zone Theories—application for Additive-Manufactured 316L Steel

Development of a Novel Fatigue Damage Model with AM Effects for Life Prediction of Commonly-Used Alloys in Aerospace

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Analysing the effect of defects on stress concentration and fatigue life of L-PBF AlSi10Mg alloy using finite element modelling

Defect tolerant fatigue assessment of AM materials: Size effect and probabilistic prospects

In situ X-ray imaging of fatigue crack growth from multiple defects in additively manufactured AlSi10Mg alloy

Predictive model to design for high cycle fatigue of stainless steels produced by metal additive manufacturing

High-Cycle Fatigue Performance of Laser Powder Bed Fusion Ti-6Al-4V Alloy with Inherent Internal Defects: A Critical Literature Review

Machine learning based very-high-cycle fatigue life prediction of AlSi10Mg alloy fabricated by selective laser melting

Micromechanics-Based Low Cycle Fatigue Life Prediction Model of ECAPed Aluminum Alloy

Fatigue Performance of Laser Powder Bed Fusion Manufactured TiB2/AlSi10Mg Composite: Experimental Investigation and Fracture Mechanics-Based Life Prediction Model for Defect Tolerance Analysis

Defect‐induced Fatigue Scattering and Assessment of Additively Manufactured 300M-Aermet100 Steel: an Investigation Based on Experiments and Machine Learning

Prediction of anisotropic LCF behavior for SLM Ti-6Al-4V considering the spatial orientation of defects