Abstract:Abstract Additive manufacturing (AM) is a developing manufacturing technology, which provides excellent attributes compared to other manufacturing techniques. However, one of the critical challenges is the presence of defects that hinder the mechanical properties of the parts, particularly the fatigue life. Experimental understanding of fatigue is a cumbersome process. Therefore, numerical prediction based on specified conditions (such as porosity and applied load) can be an alternative to experimental analysis at the design stage of AM parts. In this study, elastic–plastic finite element analysis (FEA) is performed to obtain the stress distribution around pores, and their resultant effect on fatigue life for L-PBF (laser powder bed fusion) produced AlSi10Mg alloy samples. The stress field is calculated for both single and multiple pore models, where stress concentration is evaluated as a function of the pore’s location and its size. It is found that both pore location and size affect the stress field; however, location effects dominate over pore size. For the same remote applied stress level, the stress concentration around the pore increases with an increase in pore size, and the local maximum stress occurs near the pores that are closest to the surface. The current study also evaluates the relative effect of porosity fraction, average pore size, and location. It is found that the magnitude and sensitivity of stress concentration are hierarchically controlled by porosity location, pore size, and porosity density. A multi-scale finite element (FE) model is proposed based on inherent porosity data measured using Computed Tomography (CT) to predict overall fatigue life. The fatigue cycles are calculated using the rainflow counting algorithm in FE Safe using the stress–strain data obtained from the proposed FEA model. Using the proposed model, it is possible to generate S–N curves for any loading condition for a given porosity condition (porosity density and average pore size). The S–N curve results obtained from the FE model are compared to the experimental observations. The predicted fatigue life shows approximately 5% error with experimental results at high stress loading conditions. However, the proposed model overpredicts the fatigue life at low stress loading by almost 30%.

Predictive model to design for high cycle fatigue of stainless steels produced by metal additive manufacturing

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Prediction of High Cycle Fatigue Strength for Additive Manufactured Metals by Defects Incorporated Crystal Plasticity Modeling

Development of a Novel Fatigue Damage Model with AM Effects for Life Prediction of Commonly-Used Alloys in Aerospace

Fatigue performance of metal additive manufacturing: a comprehensive overview

Machine learning based fatigue life prediction with effects of additive manufacturing process parameters for printed SS 316L

Fatigue behavior of selective laser melted 316L stainless steel: experiments and modeling

Defect‐induced Fatigue Scattering and Assessment of Additively Manufactured 300M-Aermet100 Steel: an Investigation Based on Experiments and Machine Learning

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Defect characteristics-based low-cycle fatigue life prediction model for additive manufactured Ti-6Al-4 V alloys

Analysing the effect of defects on stress concentration and fatigue life of L-PBF AlSi10Mg alloy using finite element modelling

A Multiscale High Cycle Fatigue Approach Based on Shakedown and Cohesive Zone Theories—application for Additive-Manufactured 316L Steel

Quantifying uncertainty in fatigue crack growth of SLM 316L through advanced predictive modeling

High Cycle Fatigue Behavior of 316L Steel Fabricated by Laser Powder Bed Fusion: Effects of Surface Defect and Loading Mode

The potency of defects on fatigue of additively manufactured metals

Defect tolerant fatigue assessment of AM materials: Size effect and probabilistic prospects

Defects in additive manufactured metals and their effect on fatigue performance: A state-of-the-art review

Rapid fatigue evaluation of additive manufactured specimens: Application to stainless steel AISI 316L obtained by laser metal powder bed fusion

Probabilistic prediction of the size effect on the fatigue strength for variable length specimens of selective laser melted 316L stainless steel

Data-driven fatigue life prediction in additive manufactured titanium alloy: A damage mechanics based machine learning framework

Experimental Investigation and Numerical Modelling of the Cyclic Plasticity and Fatigue Behavior of Additively Manufactured 316L Stainless Steel