Abstract:Detailed quasi-in-situ grain-by-grain slip trace analysis and EBSD analysis were performed on the as-extruded, under-aged, and peak-aged Mg–10Y (wt pct) sheets to investigate the precipitate effects on the individual slip activities and plastic heterogeneity during room temperature compression. The sheet exhibited a significant age-hardening response whose yield strength increased by 63 pct after the peak-aged treatment. In the as-extruded condition, deformation was dominated by pyramidal II ⟨c+a⟩\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\langle c + a\rangle$$\end{document} slip (42.3 pct) followed by basal ⟨a⟩\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\langle a\rangle$$\end{document} slip (31.0 pct) and then pyramidal I ⟨c+a⟩\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\langle c + a\rangle$$\end{document} slip (21.1 pct). After the peak-aged treatment, the frequency of basal ⟨a⟩\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\langle a\rangle$$\end{document} slip increased to ~ 70 pct, and the pyramidal I/II slips significantly decreased to ~ 20 pct, which indicates the precipitate strengthening on pyramidal ⟨c+a⟩\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\langle c + a\rangle$$\end{document} slips was significantly over basal ⟨a⟩\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\langle a\rangle$$\end{document} slip. Most activated slip systems (68.2 pct) exhibited large normalized Schmid factors (mnor\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${m}_{\mathrm{nor}}$$\end{document}> 0.3), but substantial (18.2 pct) hard-oriented slip systems (mnor\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$${m}_{\mathrm{nor}}$$\end{document}< 0.1) were also activated, suggesting local stress deviation. The magnitude/distribution of intragranular misorientation angle and geometrically necessary dislocation (GND) density inside a grain cannot be correlated with the visibility of slip trace from a statistical viewpoint. The extremely high GND density near grain boundary (GB) was closely related to (i) significant disparity of max Schmid factors for a particular slip mode and/or (ii) high GB misorientation between adjacent grains.

Correlation Between Dislocation Hardening and the Geometrically-Necessary-dislocation Densities in a Hexagonal-Close-packed Zr-2wt%Ti Alloy

Geometrically necessary dislocations and related kinematic hardening in gradient grained materials: A nonlocal crystal plasticity study

Resolving localized geometrically necessary dislocation densities in Al-Mg polycrystal via in situ EBSD

High Strain Gradient Plasticity Associated with Wedge Indentation into Face-Centered Cubic Single Crystals: Geometrically Necessary Dislocation Densities

Investigations of dislocation-type evolution and strain hardening during mechanical twinning in Fe-22Mn-0.6C twinning-induced plasticity steel

Effect of deformation heterogeneity on development of geometrically necessary dislocation density in heterogeneous-structured CrMnFeCoNi high-entropy alloy

Correlation of Microstructure and Tensile Properties in In-Situ High-Entropy Bulk Metallic Glass Composites

Quantifying Geometrically Necessary Dislocation Density During Hot Deformation in AA6082 Al Alloy

In-situ Analysis of Slip Transfer and Heterogeneous Deformation in Tension of Mg-5.4Gd-1.8Y-1.5Zn Alloy

Resolving crystallographic geometrically necessary dislocations in three dimensions in a hexagonal close packed titanium alloy

Local measurement of geometrically necessary dislocation densities and their strengthening effect in ultra-high deformed pearlite

The Grain Size and Orientation Dependence of Geometrically Necessary Dislocations in Polycrystalline Aluminum During Monotonic Deformation: Relationship to Mechanical Behavior

Precise Measurement of Strain Accommodation in a Mg-Gd-Y-Zn Alloy Using Cross-Correlation-based High Resolution EBSD

Investigation on Slip Activity and Plastic Heterogeneity of Aged Mg–10Y Sheets During Compression

Strain-Hardening Model of Dual-Phase Steel with Geometrically Necessary Dislocations

Multiscale discrete dislocation dynamics study of gradient nano-grained materials

Quasi-in-situ Analysis of Dependency of Deformation Mechanism and Work-Hardening Behavior on Texture in Mg-2Zn-0.1Ca Alloy

Probing deformation behavior of a refractory high-entropy alloy using in situ neutron diffraction

Effects of Precipitate on the Slip Activity and Plastic Heterogeneity of Mg-11Y-5Gd-2Zn-0.5Zr (wt. %) During Room Temperature Compression

Intergranular fracture, grain-boundary structure, and dislocation-density interactions in FCC bicrystals

A New Approach for Determining GND and SSD Densities Based on Indentation Size Effect: an Application to Additive-Manufactured Hastelloy X