Abstract:Conventional ultrasonic imaging systems use piezoelectric transducers for the generation and reception of the acoustic signal. Since its invention in 1994, the Capacitive Micromachined Ultrasound Transducer (CMUT) has been subjected to research as an alternative technology. Major advantages of the CMUT over traditional piezoelectric ultrasound transducers include higher bandwidth, higher sensitivity, CMOS compatibility, and ease of manufacturing (by the use of standard lithography techniques.) Increasing the dynamic range, decreasing the parasitic capacitance and cross coupling are the major goals in CMUT designing specially for medical imaging applications. The work in this thesis aims the optimization of a high-frequency (20 MHz) CMUT array to be used for high-resolution medical imaging. The figure of merit has been chosen as the signal-to-noise ratio of the electrical return signal, which required the construction of a model for the entire pulse-echo operation. Such a model consists of: (1) a circuit model for the device itself, (2) a model for the radiation impedance, and (3) a model for the propagation medium. The CMUT model has been extensively studied in the literature. An already existing circuit model has been used in the simulations. The radiation impedance of the CMUT array was computed using Finite Element Analysis (FEA) software packages COMSOL Multiphysics® and ANSYS®, and converted to an equivalent circuit to represent the load in the circuit simulator. The pulse-echo model, which is entirely implemented in LTspice circuit simulator, was then used to optimize CMUT parameters that include radius, membrane thickness, and gap height to maximize signal-to-noise ratio.

A Low Noise TIA with Continuous Time-Gain Compensation for Ultrasound Transducers

Low-Noise Low-Power Ultrasound AFE with Continuous TGC Built in Both TIA and Beamformer.

0.9–10GHz low noise amplifier with capacitive cross coupling

A Wideband BiCMOS Thermal Noise Canceling Low Noise Amplifier with Temperature Compensation

A BiCMOS Implementation of Noise Canceling Low Noise Amplifier for Wideband Applications

Design and test of a capacitance detection circuit based on a transimpedance amplifier

28-Nm CMOS Ultrasound AFE with Split Attenuation for Optimizing Gain-Range, Noise, and Area

Optimization of capacitive micromachined ultrasound transducers (CMUTs) for a high-frequency medical ultrasonic imaging system

Low-Power Low-Noise Amplifier Using Attenuation-Adaptive Noise Control for Ultrasound Imaging Systems

A 29.5 Dbm OOB IIP3 TIA Based on a Two-Stage Pseudo-Differential OTA with R-C Compensation and Cascode Negative Resistance

A Sub-µg Bias-Instability MEMS Oscillating Accelerometer with an Ultra-Low-Noise Read-Out Circuit in CMOS

A 164-dBΩ Transimpedance Amplifier for Monolithic CMOS-MEMS Oscillators in Biosensing Applications

Low-Noise Broadband CMOS TIA Based on Multi-Stage Stagger-Tuned Amplifier for High-Speed High-Sensitivity Optical Communication.

A Front-End CMOS Interface Circuit with High Voltage Charge Pump and Oscillator for Capacitive Micromachined Ultrasonic Transducers.

Low Power Low Noise Amplifier with DC Offset Correction at 1 V Supply Voltage for Ultrasound Imaging Systems

An RX AFE With Programmable BP Filter and Digitization for Ultrasound Harmonic Imaging

A low-complexity and high-frequency ASIC transceiver for an ultrasound imaging system

Coupling Effects of Crosstalk and Parasitic Loss on Capacitive Micromachined Ultrasonic Transducers

A 110-Dbω, 113-Mhz Variable-Gain Transimpedance Amplifier for Flash 3D Imaging Systems

Energy-Efficient Analog Frond-End Design for Ultrasound Imaging Applications

Area-efficient CMOS transimpedance amplifier for optical receivers