Abstract:Alloying is one of the effective approaches to boost the discharge property of magnesium (Mg) anodes for primary Mg-air batteries and recently micro-alloying is highly recommended at the aim of developing advanced primary Mg system. In this study, micro-alloyed extruded Mg0.5Zn0.2Ge (in wt.%) alloy is evaluated as an anode candidate for primary Mg-air batteries in both half-cell and Mg-air full cell configurations, in comparison with commercially accepted Mg anodes, typified by as-cast HP Mg and extruded AZ31 alloy. The corrosion behavior at open circuit potential (OCP) condition of the three materials is also compared through electrochemical tests. Mg0.5Zn0.2Ge alloy displays the most negative OCP value and the highest corrosion resistance at OCP. During discharge, Mg0.5Zn0.2Ge anode exhibits low wasteful-discharge rate and homogeneous dissolution that gives rise to the absence of "chunk effect". Consequently, the anodic efficiency and specific capacity of Mg0.5Zn0.2Ge anode are superior to those of HP Mg and AZ31 anodes, e.g. 57.3% and 1257 mAh g −1 at 1 mA cm −2 . Additionally, Mg-air battery based on Mg0.5Zn0.2Ge anode offers higher cell voltage and specific energy than those assembled with HP Mg and AZ31 anodes, which can be further optimized by addition of electrolyte additives. Therefore, micro-alloyed Mg0.5Zn0.2Ge alloy can serve as a promising candidate for anode material of primary Mg-air batteries.

High Anodic-Efficiency and Energy-Density Magnesium-Air Battery with Modified AZ31 Anode

Achieving Ultrahigh Anodic-Efficiency and Energy-Density Mg–air Battery Via the Discharge Product Film Design of Bulk Mg Anode

Magnesium–Air Battery with Increased Power Using Commercial Alloy Anodes

Achieving Ultrahigh Anodic Efficiency via Single-Phase Design of Mg–Zn Alloy Anode for Mg–Air Batteries

Effect of Gd content on the discharge and electrochemical behaviors of the magnesium alloy AZ31 as an anode for Mg-air battery

Electrochemical Performance of Mg-3Al Modified with Ga, in and Sn As Anodes for Mg-Air Battery

High-energy-capacity metal-air battery based on a magnetron-sputtered Mg–Al anode

Electrochemical Investigations on AZ Series Magnesium Alloys as Anode Materials in a Sodium Chloride Solution

Performance of Mg–14Li–1Al–0.1Ce As Anode for Mg-air Battery

A corrosion resistant die-cast Mg-9Al-1Zn anode with superior discharge performance for Mg-air battery

Performance of Mg-air Battery Based on AZ31 Mg Alloy Sheets with Different Grain Sizes

Effect of Y content on performance of AZ31 magnesium alloy anode in air battery

A Chloride-Free Electrolyte to Suppress the Anodic Hydrogen Evolution Corrosion of Magnesium Anode in Aqueous Magnesium Air Batteries

Hypoeutectic Mg–Zn binary alloys as anode materials for magnesium-air batteries

Performance of Mg–9Al–1In Alloy As Anodes for Mg-Air Batteries in 3.5 Wt% NaCl Solutions

An eco-friendly electrolyte additive for high-power primary aqueous Mg-air batteries

In Situ Interfacial Passivation in Aqueous Electrolyte for Mg-Air Batteries with High Anode Utilization and Specific Capacity

Magnesium-rare earth intermetallic compounds for high performance high power aqueous Magnesium-Air batteries

NaBF4-dimethyl sulfoxide/NaCl-H2O biphasic electrolytes for magnesium–air batteries

A micro-alloyed Mg-Zn-Ge alloy as promising anode for primary Mg-air batteries

Synergistic Mixture of Electrolyte Additives: A Route to a High-Efficiency Mg-Air Battery