Abstract:Owing to its high accuracy and good design flexibility, the application of laser powder bed fusion (LPBF) to metallic parts has been rapidly increasing. However, the parts fabricated using LPBF exhibit high porosity and rough texture, which severely hinders the development of this technology. In this study, typical Al-based (AlSi10Mg) and Ni-based (Inconel 718) alloys were fabricated under a wide range of parameter spaces using static magnetic field (SMF) of up to 0.2 T. The experimental results showed that the fabricated parts had a higher density with SMF than the samples fabricated without SMF. A comparison of the samples fabricated with and without SMF revealed that the SMF refined the grain size and improved the mechanical properties. Furthermore, physics-based models, including the Seebeck effect, heat transfer, and fluid flow, in melt pools dynamics were used to simulate the thermos-electric-magnetic (TEM) forces and flow patterns during LPBF. The results of the simulation suggest that at the melt pool scale, the depression zone depth increases with increasing SMF intensity, and the correspondingly increased laser absorptivity is the main reason for the decrease in the lack-of-fusion defects. In addition to the flow pattern change at the melt pool scale, the TEM force acting on the cellular dendrite also plays an important role in grain refinement, reaching 10 5 N/m 3 under a SMF of 0.1 T. Furthermore, the results of the tensile tests showed an increase in the ultimate tensile strength and elongation of the printed samples under the applied SMF. The present study can guide the porosity control and the widening of the processing window in LPBF.

Powder Fabrication and Laser Powder Bed Fusion of a MoSiBTiC-La2O3 Alloy

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

Laser Powder Bed Fusion of MoSiBTiC Alloy Powders Produced by Freeze-Dry Pulsated Orifice Ejection Method

Powder Fabrication and Laser Additive Manufacturing of MoSiBTiC Alloy

Laser Additive Manufacturing of Pure Molybdenum Using Freeze-Dry Pulsated Orifice Ejection Method-Produced Powders

Effects of Plasma Spheroidization Treatment on the Characteristics of MoSiBTiC Powders Fabricated by Freeze-Dry Pulsated Orifice Ejection Method

In-situ formation of ceramic layer on Mo-based composites via laser powder bed fusion

In-Situ Reduction of Mo-Based Composite Particles During Laser Powder Bed Fusion

A novel crack-free Ti-modified Mo alloy designed for laser powder bed fusion

Microstructure Evolution of FD-POEM Powders During High-Temperature Plasma Spheroidization

Improvement of Powder Fabrication for Additive Manufacturing Using Ultrafine Bubbles

In Situ Alloying Based Laser Powder Bed Fusion Processing of Β Ti–Mo Alloy to Fabricate Functionally Graded Composites

A Novel Approach of Fabricating Monodispersed Spherical MoSiBTiC Particles for Additive Manufacturing.

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Novel Laser Additive-Manufactured Mo-based Composite with Enhanced Mechanical and Oxidation Properties

Laser-based powder bed fusion of pre-alloyed oxide dispersion strengthened steel containing yttrium

In Situ Synthesized TiC/Mo-based Composites Via Laser Powder Bed Fusion

Processing-microstructure relationships in ferrous alloys via mixed powder laser powder bed fusion

Laser powder bed fusion of Mo2C/Ti-6Al-4V composites with alternately laminated α′/β phases for enhanced mechanical properties

Fabrication of a Strong and Ductile CuCrZr Alloy Using Laser Powder Bed Fusion

Promoting the densification and grain refinement with assistance of static magnetic field in laser powder bed fusion