Abstract:Investment casting process is an important way to get complex parts of titanium alloy. However there are few research on the interfacial heat transfer coefficient(h) between casting and shell thus the temperature simulation of investment casting process of titanium alloy is often inaccurate. In order to get a relatively accurate h,a one-dimensional mathematical model for the reverse calculation of h between casting and shell in investment casting process of Ti6Al4 V alloy was built and the analytic relationship between temperature and time/heat flux was established. Considering the calculated h is significantly affected by the error of parameters such as the specific heat capacity and thermal diffusivity of shell and position of thermocouples, research on the error of these parameters is essential. The relationship between the error of these parameters and the temperatures in the casting and shell was studied and it was found that the effect of different kind of error on the temperature field was obviously different.An experiment based on the one-dimensional mathematical model was done and temperatures of different positions were measured. Based on the effect of different kind of error and the difference between the calculate temperature field and the measured temperatures, the proportion of effect of each kind of error was assessed. These errors were revised on the basis of the assessment, thus a relatively accurate h between the casting and shell was obtained. The relationships between h and thickness of the solidified layer on the casting/temperature at the surface of casting can be divided into 4 stages:(1) Metal was liquid and h kept about 440 W/(m2·K);(2) Solid layer appeared on the surface, and h declined nearly 60%;(3) Solid layer grew up before metal became completely solid and h declined nearly 20% of its maximum;(4) After metal solidified, h declined slowly as temperature on the surface of casting dropped. These relationships were applied in a three-dimensional model for numerical simulation of the temperature field. Temperatures of different positions in casting and shell were calculated and calculated temperatures agreed with measured ones well. Thus the accuracy of h was identified and it can help solve problems in the production in investment casting process of Ti6Al4 V alloy.

INVERSE CALCULATION OF INTERFACIAL HEAT TRANSFER COEFFICIENTDURING SOLIDIFICATION OF CIRCULAR CAST STEEL CASTINGS BY NO-BAKE FURANRESIN BONDED SAND CASTING

Simulation Analysis of Thermal Stress During Casting Process of Large-Sized Alloy Steel Ingot

An Inverse Estimation of Frozen Sand Mold-Melt Heat Transfer Coefficient in the Solidification of A356 Alloy

Investigation and Application of Inverse Determination of Interfacial Heat Transfer Coefficient in Vacuum Investment Casting

Determination of Interfacial Heat Transfer Coefficient at the Frozen Sand Mold Casting Process of ZL101 Alloy

Spatial interfacial heat transfer and surface characteristics during gravity casting of A356 alloy

Measurement of Temperature Inside Die and Estimation of Interfacial Heat Transfer Coefficient in Squeeze Casting

Determination of the Interfacial Heat Transfer Coefficient at the Metal-Sand Mold Interface in Low Pressure Sand Casting

A Study of the Interfacial Heat Transfer Between an Iron Casting and A Metallic Mould

Numerical Simulation of Fluid Flow and Solidification in Continuous Slab Casting Mould Based on Inverse Heat Transfer Calculation

STUDY OF INTERFACIAL HEAT TRANSFER COEFFI-CIENT BETWEEN METAL AND DIE DURING HIGH PRESSURE DIE CASTING PROCESS OF ALUMINUM ALLOY ADCl2Z

Numerical simulation and experimental verification of the initial temperature distribution of castings during mold filling process

Numerical simulation analysis of thermal stress fields during solidification of steel casting

RESEARCH ON THE INTERFACIAL HEAT TRANSFER COEFFECIENT BETWEEN CASTING AND CERAMIC SHELL IN INVESTMENT CASTING PROCESS OF Ti6Al4V ALLOY

Study on the Heat Transfer at the Casting-Mould Interface in Resin-Bonded Sand Mould Casting of Mg-Gd-Y-Zr Alloy

RELATIONSHIP BETWEEN METAL-DIE INTERFACIAL HEAT TRANSFER COEFFICIENT AND CASTING SOLIDIFICATION RATE IN HIGH PRESSURE DIE CASTING PROCESS

Investigation of Solidification, Heat Transfer and Fluid Flow in Continuous Casting of Steel Using an Advanced Modeling Approach

Accurate Simulation of Complex Temperature Field in Counter-Pressure Casting Process Using A356 Aluminum Alloy

Numerical Methods to Improve the Computational Efficiency of Solidification Simulation for the Investment Casting Process

Study on Heat Transfer Behavior at Metal/Die Interface in Aluminum Alloy Die Casting Process - I. Experimental Study and Determination of the Interfacial Heat Transfer Coefficient

Study on the Relationship Between Interfacial Heat Transfer Coefficient and Interface Pressure in Squeeze Casting by Using Microscopic Contact Model