Abstract:The present paper focuses on the heat transfer and contact pressure at the casting-die interface in squeeze casting process. Experiments were conducted and a "plate shape" was used to cast aluminum alloy A356 in H13 steel die. Based on the temperature measurements inside the die, the interfacial heat transfer coefficient (IHTC) at the metal-die interface was determined by applying an inverse approach. The pressure at the metal-die interface was measured by using Kistler pressure transducer. The acquired data were processed by a low pass filtering method based on Fast Fourier Transform (FFT). Besides, a set of methods was set up to verify the computer program for the inverse model. The results show that the pressure at the casting-die interface and the IHTC rose to the peak value almost simultaneously as soon as the pressure was applied by the press. The higher the applied pressure, the higher the peak value of the IHTC and the pressure at the casting-die interface. It was a pressure maintaining stage immediately after the pressure was applied. During this stage, the pressure at the casting-die interface decreased immediately after it reached the peak value. The IHTC sharply dropped at the beginning. Then, the decrease rate of the IHTC became lower and lower. Besides, the IHTC of the cases with pressure applied was much higher than those without pressure applied. It indicates that the applied pressure greatly improved the contact status of casting and die surfaces and reduced the thermal resistance between the two surfaces. The IHTC profiles of the cases with the pressures 23 MPa and 46 MPa applied did not make much difference, however, when the applied pressure reached 70 MPa, the influence of the pressure at the casting die interface on the IHTC became very remarkable. (C) 2017 Elsevier Ltd. All rights reserved.

Study on the Relationship Between Interfacial Heat Transfer Coefficient and Interface Pressure in Squeeze Casting by Using Microscopic Contact Model

Experimental Study on the Heat Transfer Behavior and Contact Pressure at the Casting-Mold Interface in Squeeze Casting of Aluminum Alloy

Measurement of Temperature Inside Die and Estimation of Interfacial Heat Transfer Coefficient in Squeeze Casting

Study on the effect of die coating thickness on the interfacial heat transfer coefficient in squeeze casting of aluminum alloy

On the interfacial heat transfer and pressure transmission in squeeze casting: A case study of the sensitivity to materials

Spatial interfacial heat transfer and surface characteristics during gravity casting of A356 alloy

Investigation and Application of Inverse Determination of Interfacial Heat Transfer Coefficient in Vacuum Investment Casting

Determination of Interfacial Heat Transfer Coefficient and Its Application in High Pressure Die Casting Process

A Study on Heat Transfer at Metal/Die Interface During High Pressure Die Casting of AM60B Alloy

STUDY OF INTERFACIAL HEAT TRANSFER COEFFI-CIENT BETWEEN METAL AND DIE DURING HIGH PRESSURE DIE CASTING PROCESS OF ALUMINUM ALLOY ADCl2Z

A Mathematical Model for Simulating the Microporosity of Squeeze Casting of Aluminum Alloy

Microstructure simulation in pressurized solidification during squeeze casting of aluminum alloy A356

Study on Heat Transfer Behavior at Metal/Die Interface in Aluminum Alloy Die Casting Process - I. Experimental Study and Determination of the Interfacial Heat Transfer Coefficient

Study on Heat Transfer Behavior at Metal/Die Interface in Aluminum Alloy Die Casting Process - Ii. Effect of Process Parameters on the Interfacial Heat Transfer

Determination of the Interfacial Heat Transfer Coefficient at the Metal-Sand Mold Interface in Low Pressure Sand Casting

Determination Of The Metal/Die Interfacial Heat Transfer Coefficient And Its Application In Evaluating The Pressure Distribution Inside The Casting During The High Pressure Die Casting Process

Study on Interfacial Heat Transfer Coefficient at Metal/die Interface During High Pressure Die Casting Process of AZ91D Alloy

Temperature Measurement and Microstructure Characteristics in Squeeze Casting Aluminum Alloy Parts

Analysis of interfacial heat transfer coefficients in squeeze casting of AA6061 aluminum alloy with H13 steel die: Impact of section thickness on thermal behavior

Determination of Interfacial Heat Transfer Coefficient at the Frozen Sand Mold Casting Process of ZL101 Alloy

Effect of different processing parameters on interfacial heat-transfer behavior in high-pressure die-casting process