Abstract:Highlights • A special-shaped C sf /AZ91D composite part with a high fiber volume fraction of 23.0% was firstly prepared by the LSEVI process. • The desired configuration features were directly formed, in the way of near-net forming. • The excellent microstructure with sufficient infiltration and no fiber aggregation was obtained. • Compared with the AZ91D, the compressive strength of the composite part was effectively increased by ∼40%. To meet the increased demand for light-weight and high-performance special-shaped load bearing parts in automotive industry, the short carbon fiber reinforced magnesium matrix composite (C sf /Mg) part with complex configuration features and abrupt cross-sectional transitions was fabricated by liquid-solid extrusion following vacuum pressure infiltration process (LSEVI). Near-net forming schemes of both the special-shaped fiber preform and composite part were proposed. The effect of process parameters on the forming quality of the composite part was discussed. Meanwhile, the microstructures and compressive properties in different regions of the part were analyzed. The results show that the forward forming scheme provides the special-shaped fiber preform with no surface defects. For the C sf /AZ91D part, its internal microstructures show that the infiltration of liquid magnesium is sufficient and uniform. The compressive strength of the composite part can reach up to 487 MPa, corresponding to ∼40% increase compared to 335 MPa of the AZ91D alloy. The average compressive strain of composites is less than 10%, which is about 50% of that of the AZ91D alloy. When the fiber orientation is parallel to the shear direction on the shear plane, the load-bearing capacity of the fiber is much higher than that of the fiber perpendicular to the shear direction. This work not only provides a convenient approach to fabricate special-shaped preform with high fiber volume fraction, but also gives a demonstration for the near-net forming of C sf /Mg parts with excellent material isotropy and compressive properties. Graphical abstract Download : Download high-res image (275KB) Download : Download full-size image

Influence of Microstructures on Mechanical Properties of the Csf/Mg Composite Fabricated by Liquid-Solid Extrusion Following Vacuum Pressure Infiltration

Microstructures and Mechanical Properties of Engineered Short Fibre Reinforced Aluminium Matrix Composites

Effect of fabrication parameters on carbon fibre reinforced magnesium matrix composite components

Tensile and fatigue behavior of carbon fiber reinforced magnesium composite fabricated by liquid-solid extrusion following vacuum pressure infiltration

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Study of the C/ Mg Interface in Magnesium Matrix Composites Reinforced by Carbon (Graphite) Fiber

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Fabrication and Mechanical Properties of Mesoporous Silica Nanoparticles Reinforced Magnesium Matrix Composite

Strengthening Mechanism and Damping Properties of SiCf/Al-Mg Composites Prepared by Combining Colloidal Dispersion with a Squeeze Melt Infiltration Process

Preparation of the high compressive performance special-shaped C sf /AZ91D composite part using the liquid-solid extrusion following vacuum pressure infiltration process

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Effects of Cyclic Extrusion and Compression on the Microstructure and Mechanical Properties of AZ91D Magnesium Composites Reinforced by SiC Nanoparticles

Effects of interfacial diffusion induced infiltration process on the microstructure evolution and interfacial enhancement of CF/Mg composites

An analysis of the factors affecting strengthening in carbon fiber reinforced magnesium composites

Effects of optimizing continuous forging extrusion process on the microstructure and mechanical properties of AZ31 magnesium alloy

Study of Microstructure and Mechanical Properties of Short Carbon Fibers Reinforced Mg Matrix Composites Fabricated by Hot Extrusion

Microstructure and Mechanical Property of Nano-Sicp Reinforced High Strength Mg Bulk Composites Produced by Friction Stir Processing

Experimental study on properties and structure of magnesium alloy/PC/ABS hybrid materials prepared by hot-press molding technology

Effect of hot extrusion on the microstructure and mechanical properties of SiCNWs/Mg-2Zn-0.1Y composite

Micro-structural and tensile strength analyses on the magnesium matrix composites reinforced with coated carbon fiber