Abstract:This study examines the mechanical properties and wear mechanisms of magnesium (Mg) metal matrix composites reinforced with titanium (Ti) and silicon carbide (SiC) particles. Three different composite formulations were investigated: Mg-30 wt% Ti (A), Mg-25 wt% Ti-5 wt.% SiC (NB), Mg-20 wt% Ti-10 wt% SiC (NC), and Mg-15 wt% Ti-15 wt% SiC (ND). These composites were fabricated through ball milling and spark plasma sintering (SPS). The incorporation of SiC particles significantly enhanced grain refinement and phase formation within the composites. Density analysis revealed that the actual densities of the composites were lower than the theoretical values, with Composite A exhibiting the highest actual density of 2.15 g/cm3 and the lowest porosity of 16.31%. The introduction of SiC particles increased porosity, with Composite NB displaying the highest porosity at 30.58%. Hardness testing indicated that Composite NC, containing 10 wt% SiC, achieved the highest hardness of 137 HV. In contrast, Composite ND, with 15 wt% SiC, showed a reduced hardness of 115 HV, attributed to increased porosity and potential SiC particle agglomeration. Wear behavior was evaluated using a pin-on-disc tribometer. Weight loss measurements indicated that Composite A had the lowest weight loss (1.1–2.1 mg), while Composite NB experienced the highest weight loss (2.8–8.3 mg) due to increased porosity. Composite NC demonstrated a balance with moderate weight loss (2.0–3.8 mg). The coefficient of friction (COF) varied with SiC content and applied loads (2, 4, and 8 N), with Composite A demonstrating the lowest COF values (2.3–2.8) and stable performance across different loads. Composite NB exhibited higher COF values (3.5–4) and significant fluctuations due to elevated porosity and the presence of SiC particles. Composite NC showed better wear resistance and more stable COF values (2.5–2.9) compared to NB and ND.

Microstructure and Mechanical Property of Nano-Sicp Reinforced High Strength Mg Bulk Composites Produced by Friction Stir Processing

Magnesium-based nanocomposites synthesized using friction stir processing: an experimental study

Microstructure Evolution and Mechanical Properties of Sic Nanoparticles Reinforced Magnesium Matrix Composite Processed by Cyclic Closed-Die Forging

Enhancing microstructural and mechanical properties of magnesium AZ31 matrix composites through friction stir processing incorporating silicon carbide, titanium carbide, and graphite particles

Preparation and properties of nano-sized SiC particles reinforced AZ91D magnesium matrix composites

Enrichment in Fracture Ductility Tribological Characteristics of Magnesium-Based Nanocomposites Fabricated via Multi-pass Friction Stir Processing and Study of Significant Parameters

Mechanical properties and corrosion behavior of a friction stir processed magnesium alloy composite AZ31B–SiC

Magnesium‐based nanocomposites developed through multi‐pass friction stir processing and strengthening mechanisms exploration

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Microstructure and mechanical properties of carbon nano-onions reinforced Mg-based metal matrix composite prepared by friction-stir processing

Effect of SiC on Microstructure and Mechanical Properties of Nano-SiC/Mg-8Al-1Sn Composites

Fabrication and Mechanical Properties of Mesoporous Silica Nanoparticles Reinforced Magnesium Matrix Composite

Mechanical Properties and Microstrutures of Nano-Sized Sic Particles Reinforced Az91d Nanocomposites Fabricated by High Intensity Ultrasonic Assisted Casting

A Novel Way to Produce Bulk SiCp Reinforced Aluminum Metal Matrix Composites by Friction Stir Processing

Synthesis and characterization of magnesium-titanium carbide nanocomposites via friction stir processing: An in-depth parameter investigation

Mg/ZrO2 Metal Matrix Nanocomposites Fabricated by Friction Stir Processing: Microstructure, Mechanical Properties, and Corrosion Behavior

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Development of a Magnesium/Amorphous Nano-SiO2 Composite using Accumulative Extrusion Method

Parametric Influence of Friction Stir Processing on Microstructural Evolution and Tensile Behavior of AZ31/Ti-6Al-4V Magnesium Matrix Composites

Magnesium Matrix Nanocomposites Fabricated by Ultrasonic Assisted Casting