Abstract:Spiral fibers were considered to be an ideal toughening phase of ultra-high torsional release effect. In this work, ZrB2 (Z)-20 vol% SiC (S) spiral fiber (ZS(sf)) with controllable structure was prepared by a combination approach of liquid rope effect and non-solvent-induced phase separation. Dominantly depended on the kinematic viscosity (.), dropping height (H), and flow rate (Q), the geometric parameters of ZSsf involving filament diameter (d) and coil diameter (D) were followed the relationship of d approximate to 0.516x10(-3)Q(1/2)H(-1/4) and D approximate to 0.25x10(-3)(Q/H)(1/3), respectively, within the optimized. of 10-15 Pa center dot s. Three different microstructures of ZS(sf) were achieved by adjusting the polymer/solvent/ non- solvent system assisted with phase diagram calculation, including dense, hollow, and hierarchical pore structures. The ZrB2-SiC with 1 wt% ZS(sf) composites prepared by hot isostatic pressing (HIP) exhibited a similar to 30% increase in fracture toughness (K-IC, 4.41 MPa center dot m(1/2)) compared with the ZrB2-SiC composite, where the microscopic fracture toughness of the ZS(sf) was similar to 80% higher than that of the matrix. The fibers with a similar to 10 nm in-situ-synthesized graphite phase amongst grain boundaries of ZrB2 and SiC changed the fracture mode, and promoted the crack deflection and pull-out adjacent the interface of matrix and the fiber.

ZrB2–SiC Spiral Fibers Prepared by Combining Liquid Rope Effect with Non-Solvent-induced Phase Separation Method: A Promising Toughening Material for Ultra-High Temperature Ceramics

Microstructural Evolution and Performance of Carbon Fiber-Toughened ZrB2 Ceramics with SiC or ZrSi2 Additive

Analysis of the Mechanical Properties in Short Carbon Fiber-toughened ZrB2—SiC Ultra-high Temperature Ceramic

Effects of Short Carbon Fiber on Mechanical Properties of ZrB2-SiC Ultra-high Temperature Ceramics

Microstructure, Mechanical Properties and Thermal Shock Resistance of ZrB 2 -Sic-c F Composite with Inhibited Degradation of Carbon Fibers

Mechanical Properties of Short Carbon Fiber Reinforced ZrB2–SiC Ceramic Matrix Composites

Processing, microstructure, and mechanical properties of chopped SiC fibers reinforced ZrB2–hBN–based composites

Characterization of hot-pressed short carbon fiber reinforced ZrB2–SiC ultra-high temperature ceramic composites

Influence of the Microstructure Evolution of ZrO2 Fiber on the Fracture Toughness of ZrB2–SiC Nanocomposite Ceramics

Novel Ti3SiC2-(Ti, Zr)B2 Toughened (ti, Zr)C-based Composites with Enhanced Mechanical Properties Fabricated by Dual in Situ Reactions Hot-Pressing at Low Temperature

Fabrication and mechanical properties of ZrB2–SiCw ceramic matrix composite

Fabrication and Properties of Short Carbon Fiber-ZrB2 Ceramic Matrix Composites

The hybrid effect of SiC whisker coupled with ZrO 2 fiber on microstructure and mechanical properties of ZrB 2-based ceramics

Microstructure and mechanical properties of ZrB2–SiC–ZrO2f ceramic

High-Performance Zrb2-Sic-C-F Composite Prepared by Low-Temperature Hot Pressing Using Nanosized Zrb2 Powder

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Preparation and Characterization of High-Performance ZrB 2 –sic–cf Composites Sintered at 1450 °C

Processing and Mechanical Properties of Short Carbon Fibers Toughened Zirconium Diboride-Based Ceramics

Toughened (ti0.2zr0.2hf0.2nb0.2ta 0.2)B2-Sic Composites Fabricated by One-Step Reactive Sintering with a Unique SiB6 Additive

Effect of Pyrolytic Carbon Coating on the Microstructure and Fracture Behavior of the Cf/ZrB2-SiC Composite

Characterization and mechanical properties of Cf/ZrB2-SiC composites fabricated by a hybrid technique based on slurry impregnation, polymer infiltration and pyrolysis and low-temperature hot pressing