Abstract:A Co-Ni-Cu multiprincipal element alloy (MPEA) powder was successfully synthesized through coprecipitation. Results of energy dispersive spectroscopy (EDS) and X-ray fluorescence spectroscopy (XRF) revealed nearly equal atomic ratios for Co, Ni, and Cu in the Co-Ni-Cu MPEA powder. Moreover, X-ray diffraction (XRD) confirmed a single-phase face-centered cubic (fcc) structure in the Co-Ni-Cu MPEA powder. To explore the differences in microstructure and mechanical properties, we compared a novel WC-2Co-2Ni-2Cu cemented carbide, utilizing the Co-Ni-Cu MPEA as a binder, with conventional WC-6Co and WC-3Co-3Ni cemented carbides prepared via liquid phase sintering. This comparison was conducted using scanning electron microscopy, XRD, and mechanical properties testing. Observations revealed that the surfaces of WC grains in WC-2Co-2Ni-2Cu and WC-6Co appeared smooth and flat, while those in WC-3Co-3Ni exhibited roughness with numerous terraces. In addition, the average grain size was 0.96, 1.14, and 1.22 mu m in WC-2Co-2Ni-2Cu, WC-6Co, and WC-3Co-3Ni, respectively. Notably, the Co-Ni-Cu MPEA inhibited WC grain growth. WC-2Co-2Ni-2Cu (1388 HV30) exhibited hardness similar to that of WC-6Co (1406 HV30) but the highest fracture toughness (9.04 MPa center dot m(1/2)), while WC-3Co-3Ni (1332 HV30) presented the lowest hardness. Bending strength values were recorded at 2406 MPa for WC-2Co-2Ni-2Cu, 2816 MPa for WC-6Co, and 2645 MPa for WC-3Co-3Ni, with WC-6Co exhibiting the highest bending strength. Considering their microstructures, physical properties, and mechanical properties comprehensively, the novel cemented carbides exhibited only slightly reduced bending strength compared to conventional counterparts. Thus, the Co-Ni-Cu MPEA binder demonstrates promising potential as a replacement for the conventional Co metal binder.

Additive manufacturing of cemented carbide using analogous powder injection molding feedstock

Material extrusion printing of WC-8%Co cemented carbide based on partly water-soluble binder and post-processing

Material extrusion additive manufacturing of WC-9Co cemented carbide

Additive manufacturing of WC-Co cemented carbides: process, microstructure, and mechanical properties

Additive Manufacturing of Cemented Carbides Inserts with High Mechanical Performance

Carbon control and densification of WC-8%Co fabricated by extrusion-based additive manufacturing under pressureless sintering

Fabrication of spherical WC-Co powders by radio frequency inductively coupled plasma and a consequent heat treatment

High-performance WC-AlCoCrFeNi 2.1 cemented carbides fabricated by resistance seam additive manufacturing

Printability and Properties of Tungsten Cemented Carbide Produced Using Laser Powder Bed Fusion Additive Manufacturing with Ti As a Binder

Binder jetting 3D printed cemented carbide: Mechanical and wear properties of medium and coarse grades

Laser powder bed fusion of cemented carbides by developing a new type of Co coated WC composite powder

Shape Retention of Cemented Carbide Prepared by Co Melt Infiltration into Un-Sintered WC Green Parts Made Via BJ3DP

Role of Co Content on Densification and Microstructure of WC–Co Cemented Carbides Prepared by Selective Laser Melting

Microstructures and Properties of a Novel Cemented Carbide Prepared Using a Co–Ni–Cu Multiprincipal Element Alloy As the Binder

WC-18wt.% Co with simultaneous improvements in hardness and toughness derived from nanocrystalline powder

A short and facile process to synthesize WC-Co cemented carbides

High-gravity Combustion Synthesis and in Situ Melt Infiltration: A New Method for Preparing Cemented Carbides

Two-material Powder Injection Molding of Functionally Graded WC–Co Components

Correlation of Different Cemented Carbide Starting Powders with the Resulting Properties of Components Manufactured via Binder Jetting

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Control morphology and properties in additive manufacturing of functional gradient cemented carbides for polycrystalline diamond substrates