Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. A multi-grain conical grinding head capable of performing both peripheral and end-face grinding was created in Abaqus to simulate conventional grinding (CG) and axial ultrasonic-assisted vibration grinding (AUVAG) on Ti-6Al-4V alloy. A comparative analysis was conducted to examine the effects of key grinding parameters on the fluctuation amplitude and mean value of grinding forces in CG and AUVAG. The mechanism of ultrasonic vibration's influence on grinding forces was analyzed, and a theoretical model for normal and tangential grinding forces in peripheral grinding of Ti-6Al-4V was established. Additionally, the surface morphology of CG and AUVAG was analyzed. The study found that the fluctuation amplitude of grinding forces in both AUVAG and CG increases with the axial grinding depth, feed rate, ultrasonic amplitude, and ultrasonic frequency, while it decreases with increasing spindle speed. However, the fluctuation amplitude in AUVAG is greater than that in CG. The average grinding forces in both CG and AUVAG increase with the grinding depth and feed rate, and decrease with the spindle speed. Compared to CG, the mean Fx ([math]) and Fy ([math]) are lower in AUVAG, while the mean Fz ([math]) is higher. Under different axial grinding depths, the maximum reduction in [math] and [math] for AUVAG is 4.70% and 5.18%, respectively, while the maximum increase in [math] is 77.48%. At different feed rates, the maximum reduction in [math] and [math] for AUVAG is 3.02% and 21.01%, respectively, while the maximum increase in [math] is 81.67%. Under different spindle speeds, the maximum reduction in [math] and [math] is 7.20% and 17.82%, respectively, and the maximum increase in [math] is 281%. As the ultrasonic amplitude and frequency increase, [math] significantly rises, but the effect on [math] and [math] is weak. AUVAG improves the surface quality of the specimen.

Study on Surface Creation Law of Planar Two-Dimensional Ultrasonic-Assisted Abrasive Belt Grinding

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

Study on the system matching of ultrasonic vibration assisted grinding for hard and brittle materials processing

Study on Grinding Force Model in Ultrasonic Vibration Assisted Grinding for Ductile Materials

Research on the System Matching Model in Ultrasonic Vibration-Assisted Grinding

Studies on the Surface Quality of the Unsteady-State Grinding Technique

Surface roughness model of ultrasonic vibration-assisted grinding GCr15SiMn bearing steel and surface topography evaluation

Modeling and Simulation of Grinding Surface Topography Considering Wheel Vibration

Generation Mechanism Modeling of Surface Topography in Tangential Ultrasonic Vibration-Assisted Grinding with Green Silicon Carbide Abrasive Wheel

Mechanism study on ultrasonic vibration assisted face grinding of Hard and brittle materials

Study on grinding performance during ultrasonic vibration-assisted grinding ultra-high strength steels

Grinding force assessment in tangential ultrasonic vibration-assisted grinding gear: Analytical model and experimental verification

Modeling and experimental study of surface generation in ultrasonic vibration-assisted grinding of Ti-6Al-4V micro-channels

Multi-Step Two-Dimensional Ultrasonic-Assisted Grinding of Silicon Carbide: An Experimental Study on Surface Topography and Roughness

Effect of intermittent cutting behavior on the ultrasonic vibration-assisted grinding performance of Inconel718 nickel-based superalloy

Study on surface formation mechanism of multiple abrasive particles under ultrasound

Research Status and Future Prospects of Ultrasonic Vibration-assisted Grinding Technology and Equipment

Alumina abrasive wheel wear in ultrasonic vibration-assisted creep-feed grinding of Inconel 718 nickel-based superalloy

Analytical modeling of abrasive grain-workpiece cutting coefficient and experimental investigation on tangential ultrasonic vibration-assisted forming grinding gear

Research on the effect of grinding force on the axial ultrasonic vibration-assisted grinding of Ti-6Al-4V with multi-grain conical grinding head

Surface quality and cylindricity of ultrasonic elliptical vibration–assisted centerless grinding of micro-rod YAG single crystals