Abstract:In this paper, efforts have been dedicated to electrodeposit nanocrystalline Ni-W-Co ternary alloy film on copper substrate through electrodeposition in sulfate-citrate bath. Effects of electrodeposition parameters such as Co ion concentration, applied current density, electrolytic bath pH and deposition time on structural, composition, surface characteristics and corrosion properties of Ni-W-Co alloys were explored. Corrosion and wear behaviors were evaluated. It proved that Ni-W-Co alloy has a uniform, compact and flatter surface, exhibiting colony-like morphology. Amorphous or nanocrystalline structure was formed depending on the process parameters including current density, pH and electrolyte composition. The crystallite size was little affected by Co content but greatly affected by current, bath pH and the duration of plating time. The average roughness Ra was optimized to 4–7 nm. This ternary alloy contains 33 wt% W, 21–60 wt% Ni and 2.8–40 wt% Co. In the alloy, the decrease of nickel content corresponds to the increase of Co and vice versa. W content varied little with the change of electrodeposition conditions. Co content slightly decreases as current density increases. Increasing bath pH greatly decreases the Co contents and increases the Ni content. A ternary complex [M(HWO4)(C6H5O7)]2−(M = Ni, Co) in solution is crucial for the formation of Ni-W-Co alloy. The optimized process parameters for best corrosion and wear resistance were 5–8 mA cm−2, 55 min, 0.1 mol L−1 Co2+ and pH = 6.

Microstructure and tribological properties of electrodeposited Ni–Co alloy deposits

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Electrodeposition and corrosion performance of Ni-Co alloys with different cobalt contents

Effect of Sn addition on the tribological behaviors of CoCrFeNi high entropy alloys

Effect of Cobalt Content on the Properties of Nickel-Cobalt Alloy Coatings

Electrodeposition of Ni–Co alloys from a deep eutectic solvent

Effect of Surface Roughness and Structure Features on Tribological Properties of Electrodeposited Nanocrystalline Ni and Ni/Al2O3 Coatings

Electrochemical deposition and tribological behaviour of Ni and Ni–Co metal matrix composites with SiC nano-particles

Tailoring role of Al and Ti particles in the microstructure and property of electrodeposited Ni matrix nanocomposite coatings

Effect of cobalt content on electrodeposition and properties of Co–Ni alloy thin films

Influences of Co and process parameters on structure and corrosion properties of nanocrystalline Ni-W-Co ternary alloy film fabricated by electrodeposition at low current density

Effect of Cobalt on Microstructure and Wear Resistance of Ni-Based Alloy Coating Fabricated by Laser Cladding

Effect of cobalt content on the microstructure, microtexture, and mechanical properties of W-Ni-Fe-xCo alloys during solid-phase-sintering and liquid-phase-sintering

Effect of WC-12Co on the mechanical and wear performance of laser melting deposition nickel-based alloy

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Effects of Co Addition on the Microstructure and Properties of Elastic Cu-Ni-Si-Based Alloys for Electrical Connectors

Effect of Cu-doping on tribological properties of laser-cladded FeCoCrNiCu x high-entropy alloy coatings

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Mechanisms underlying the influence of Co and Ti on the microstructure, mechanical and wear properties of A2/B2 typed AlCrFeNi alloy

An atomic insight into the stoichiometry effect on the tribological behaviors of CrCoNi medium-entropy alloy

Investigations on the microstructures and tribological behaviors of as-cast CrFeCoNiCu x high entropy alloys