Design and Fabrication of Button-Style Beam Position Monitors for the HEPS Synchrotron Light Facility

Jun He,Yan-Feng Sui,Yong Li,Xu-Hui Tang,Lin Wang,Fang Liu,Zhi Liu,Ling-Da Yu,Xiao-Yu Liu,Tao-Guang Xu,Jian-She Cao,Jun-Hui Yue

DOI: https://doi.org/10.1007/s41365-022-01126-7

2022-01-01

Nuclear Science and Techniques

Abstract:At the High Energy Photon Source (HEPS), a high orbital stability of typically 10

What problem does this paper attempt to address?

Design of Button Beam Position Monitor for Hefei Light Source

MA Tian-ji,SUN Bao-gen,YANG Yong-liang,LU Ping,FANG Jia,ZOU Jun-ying

2010-01-01

Abstract:The calculation of relevant parameters of the button beam position monitor (BPM) at Hefei Light Source (HLS) was presented. The horizontal and vertical sensitivity were calculated. The intrinsic resolution and transmission power were calculated under certain parameters. The high precision beam position was simulated with the optimized detector installation location parameters. The measured data were processed by the difference/sum and log-ratio method to obtain the intuitive mapping figure and fitting polynomial. The sum signal was simulated and fitted. The variety range of normalized sum signal was less then 5×10—3 when the beam displacement changed from (0 mm,0 mm) to (4 mm,4 mm).
Optimization of the Cavity Beam-Position Monitor System for the Shanghai Soft X-ray Free-Electron Laser User Facility

Chen Jian,Leng Yong-Bin,Yu Lu-Yang,Lai Long-Wei,Yuan Ren-Xian

DOI: https://doi.org/10.1007/s41365-022-01117-8

2022-01-01

Nuclear Science and Techniques

Abstract:To achieve high-efficiency operation of the high-gain free-electron laser (FEL), the electron beams and radiated photon beams need to be overlapped precisely and pass through the entire undulator section. Therefore, a high-resolution beam-position monitor (BPM) is required. A cavity BPM (CBPM) with a resonant cavity structure was developed and used in the Shanghai Soft X-ray FEL (SXFEL) test facility and can achieve a position resolution of $$< {1}\upmu \mathrm{m}$$ . The construction and operation of the SXFEL user facility also bring about higher requirements for beam-position measurement. In this case, the factors that affect the performance of the CBPM system were further analyzed. These included the amplitude and phase stability of the local oscillator, stability of the trigger signal, performance of the radio frequency front-end, signal processing electronics, and signal processing algorithms. Based on the upgrade and optimization of the system, a beam test platform was built at the end of the linear acceleration section of the SXFEL, and the experimental results show that the position resolution of the system can reach 177 nm at a bunch charge of 500 pC, and the dynamic range is controlled within $$\pm {300}\upmu \mathrm{m}$$ , and the relative measurement uncertainty of the bunch charge can reach 0.021 $$\%$$ , which are significant improvements compared to the attributes of the previous system.
Design of the Button-Type Beam Position Monitor for the Electron Storage Ring of Hefei Advanced Light Facility

Jianye Wang,Dongyu Wang,Anxin Wang,Baogen Sun,Ping Lu,Leilei Tang

DOI: https://doi.org/10.1109/icetis61828.2024.10593791

2024-01-01

Abstract:There are large number of button-type beam position monitors (BPMs) installed on the electron storage ring of the Hefei Advanced Light Facility (HALF), which primarily used for measuring the beam position and closed orbit. This paper presents the design of the button-type BPM for the diffraction-limited storage ring of the HALF. Firstly, the design of the button-type BPM, including materials and geometric structures, is based on the requirements of the measurement system. Subsequently, simulations and numerical analyses are applied to evaluate the pickup signal strength and sensitivity of the button-type BPM. Furthermore, 3D electromagnetic simulations are employed to get the wakefield losses when the electron beam passed through the button-type BPM. Based on the wakefield loss factor, the temperature distribution and mechanical thermal deformation caused by the dissipation of beam wakefield power on the geometric structure of the button-type BPM are analysed. The results of the multiphysics field simulations consist of electromagnetic, thermal, and mechanical aspects of the button-type BPM model show that the design of the BPMs satisfy the beam position measurement for the HALF. The mechanical structure and key component materials for the fabrication of the button-type BPM for the HALF storage ring were determined.
SXFEL LINAC BPM SYSTEM DEVELOPMENT AND PERFORMANCE EVALUATION ∗

Fangzhou Chen,Jian Chen,Longwei Lai,Yongbin Leng,Tong Wu,Luyang Yu,Renxian Yuan

DOI: https://doi.org/10.18429/jacow-ipac2018-thpml067

2018-01-01

Abstract:Shanghai Soft X-ray Free Electron Laser (SXFEL) is a test facility to study key technologies and new FEL physics. In order to deliver high quality electron beams to the undulator section, a high resolution (better than 10 microns with 200 pC beam) Linac beam position monitor system has been developed. The system consists of stripline pickup and custom designed DBPM processor. The hardware and software architecture will be introduced in this paper. The online performance evaluation results will be presented as well. BACKGROUND SXFEL SXFEL is one of the high-gain FELs constructed in China. Key technologies have been tested through prototype developments. Based on the research and development prototype of hard X-ray FEL. The construction of the user facility in soft XFEL has already finished. The SXFEL facility consists of an electron injector with a thermionic cathode, main accelerate section including C-band high-gradient accelerators along with S-band accelerators, and in-vacuum undulators. Fig. 1 is SXFEL injector layout [1]. SXFEL Figure 1: SXFEL injector layout. is designed to generate a coherent x-ray beam using a selfamplified spontaneous emission (SASE) process. Below is the baseline parameters of SXFEL. In order to meet the harsh demands, the beam diagnostic system achieving high precision resolution is one of the most important technical issues. Demands for the precise measurement of the resolution of the SXFEL LINAC system. LINAC BPM System As the key beam diagnostics tool, BPM systems are widely equipped in all kinds of accelerators. Stripline Beam Position Monitors (SBPM) are main beam diagnostic instruments ∗ Work supported by The National Key Research and Development Program of China (Grant No. 2016YFA0401900, 2016YFA0401903) † chenfangzhou@sinap.ac.cn ‡ lengyongbin@sinap.ac.cn in SXFEL. There are six SBPMs conducted in SXFEL injector section and nearly thirty SBPMs conducted in LINAC section in injector section used for the measurement and adjustment of beam orbit. Moreover, the sum of four SBPM electrodes signal can also apply in relative beam charge measurement. Fig. 2 is the block diagram of SBPM system. RF cable extract beam signal from SBPM pickup, RF signal conditioning circuit to digital BPM processor. Figure 2: BPM system block diagram Stripline BPM Since the size of the beam pipe is different, there are two kinds of SBPM with different K values in SXFEL. One of the beam pipe diameter is 16 mm while the K value is 5.24, the other is 25 mm while the K value is 7.59. The installation of the SBPM in SXFEL is different from the BPM installed in SSRF, we adopt horizontal and vertical installation mode. In that way, horizontal and vertical beam position measurement is mutual independence.Fig. 3(a) is the picture of stripline BPM. Figure 3: Stripline BPM and DBPM processors in SXFEL. DBPM processor The DBPM processors are custom designed to measure the beam positions, every beam position monitors is connected to a digital BPM processor. The centre frequency of the DBPM processor is 500 MHz, and the bandwidth is 20 MHz. The processor is carried a 16 bit high-resolution ratio ADC and advanced FPGA chip. The arithmetic of beam position is using Hilbert transform to exact the amplitude, using Δ − Σ arithmetic calculate the beam position. Fig. 3(b)is some of the DBPM processors conducted in the SXFEL technical corridor and Fig. 4 is SXFEL edm panel. 9th International Particle Accelerator Conference IPAC2018, Vancouver, BC, Canada JACoW Publishing ISBN: 978-3-95450-184-7 doi:10.18429/JACoW-IPAC2018-THPML067 THPML067 4794 Co nt en tf ro m th is w or k m ay be us ed un de rt he te rm so ft he CC BY 3. 0 lic en ce (© 20 18 ). A ny di str ib ut io n of th is w or k m us tm ai nt ai n at tri bu tio n to th e au th or (s ), tit le of th e w or k, pu bl ish er ,a nd D O I. 06 Beam Instrumentation, Controls, Feedback, and Operational Aspects T03 Beam Diagnostics and Instrumentation Figure 4: SXFEL EDM panel.
Beam instrumentation system for shanghai soft x-ray fel test facility*

L. W. Lai,L. Y. Yu,Y. B. Leng,R. X. Yuan,J. Chen,Y. B. Yan,W. M. Zhou,S. S. Cao,L. H. Hua,B. Gao,N. Zhang,T. Shen,F. Z. Chen,R. T. Jiang,W. C. Fang,C. Feng,SSRF

2020-01-01

Abstract:Shanghai Soft-Xray FEL (SXFEL) test facility was designed and built to demonstrate EEHG and HGHG schemes and verify key technologies for the future hard xray FEL facility (SHINE). After three years commissioning 8.8 nm FEL radiation with peak power of 1 MW had been achieved at the end of 2019. The design, fabrication, commissioning and operation of BI system including striplineBPM, Cavity-BPM, screen monitor, bunch length monitor, beam arrival monitor, bunch energy monitor, will be introduced in this paper. Several lessons learned during design stage and beam commissioning stage, such as radiation damage of CCDs and step-motors, bad choice of CBPM working frequency, thermal drift of BAM and so on, will be addressed as well. INTRODUCTION SXFEL Test Facility (SXFEL-TF) was initiated in 2006 and founded in 2014. Its 0.84GeV linac and undulators were installed through 2016 to 2018, it is for testing the cascaded seeding schemes. The main parameters are listed in Table 1. The SXFEL-TF commissioning has completed this year, and the SXFEL user facility (SXFEL-UF) is under construction. The layout of SXFEL-TF and SXFEL-UF are shown in Figure 1. Table 1: SXFEL-TF Parameters Parameter Value Total length 293m Electron energy 0.84 GeV Bunch charge 0.5 nC Repetition rate 10 Hz FEL output 8.8 nm FEL scheme HGHG/EEHG FEL pulse 100-200 fs FEL power >100 MW Figure 1: Layout of SXFEL-TF (top) and SXFEL-UF (bottom). In order to maintain high FEL gain, high performance beam instrumentation system is required for the SXFELTF. Measured beam parameters including bunch charge, beam position (BPM), beam profile, beam arrival time (BAM) and bunch length (BLM). Table 2 lists the beam diagnostic devices included and the required resolution. Table 2: Requirements of SXFEL-TF Diagnostic System
Button-Type Beam Position Monitor Development for Fourth-Generation Synchrotron Light Sources: Numerical Modeling and Test Bench Measurements

Stefano Cleva,Silvano Bassanese,Massimiliano Comisso,Moussa El Ajjouri,Rudi Sergo,Christian Morello,Andrea Passarelli

DOI: https://doi.org/10.3390/s24092726

IF: 3.9

2024-04-26

Sensors

Abstract:This paper addresses the design of beam position monitor (BPM) devices suitable for fourth-generation diffraction-limited X-ray storage rings. Detailed investigations of the electromagnetic (EM) phenomena occurring inside the component under various working conditions are carried out by considering different BPM EM models defined by their geometry and materials. Moving from a theoretical characterization of the common round geometry, rhomboidal structures are studied through a careful numerical analysis relying on advanced computer-aided tools. Several critical elements, such as wakefields, pick-up signal extraction, and trapped and propagating modes, are explored from the simulation point of view and from the experimental one, by deploying a manufactured microwave test bench, which is employed to measure the radio frequency behavior of a BPM prototype built at Elettra Sincrotrone Trieste. The aim of the proposed study is to identify a satisfactory tradeoff between achievable performance and practical realizability for BPM devices operating in last-generation light sources.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Design of fast beam transverse profile monitor in electron storage ring

Chaocai CHENG,Baogen SUN,Yongliang YANG,Zeran ZHOU,Ping LU,Fangfang WU,Jigang WANG,Kai TANG,Qing LUO,Hao LI

DOI: https://doi.org/10.11889/j.0253-3219.2015.hjs.38.070104

2015-01-01

Nuclear Techniques

Abstract:Background: Many issues such as beam dynamics and beam instability concerning machine performance and stability are being studied in accelerator facility. As a consequence, a Fast Beam Transverse Profile Monitor (FBPM) using visible synchrotron radiation is being developed and will be applied for the upgrade project of Hefei Light Source (HLS II).Purpose: This study aims to design a FBPM apparatus to measure beam position and size in electron storage ring.Methods: A Hamamatsu Multi-Anode Photo-Multiplier Tube (MAPMT) R5900U-00-L16 is applied to the development of FBMP. This MAPMT has a 0.8 mm′16 mm effective area per channel and 0.6 ns typical rise time which has enough spatial and temporal resolution. Logarithm processing technique with four successive channels is used to acquire beam parameters.Results: The test results show that measurement errors of focal length are within±1 mm, bandwidth of low noise wideband amplifier is approximately 420 MHz, gain errors between all the four channels and the second channel are less than 0.2 dB, and peak signal errors among them are no more than 2%.Conclusion: The FBMP apparatus proposed in this paper meet the requirements of acquiring beam turn-by-turn transverse beam position and size with only four channels of MAPMT.
Calibration of Button Type Beam Position Monitor for HLS Ⅱ

Yong-liang YANG,Chao-cai CHENG,Bao-gen SUN,Tian-ji MA,Ping LU,Jun-ying ZOU

DOI: https://doi.org/10.7538/yzk.2014.48.03.0541

2014-01-01

Abstract:According to the high precision requirements of the Hefei Light Source major maintenance and reconstruction project , a new button type beam position monitor (BPM) was designed for HLS Ⅱ electron storage ring .The characteristic impedance and distributed capacitance of button pickup were measured by time-domain reflectometer (TDR) ,and scaling coefficient of the new BPM was determined through antenna method .The TDR test results show that the impedance of pickup is 50 Ω which matches the cable impedance ,and the capacitance is about 2.9 pF w hich meets design requirements . Furthermore , the intuitive mapping diagram and calibration factor of beam position were obtained by antenna scanning .Compared with the design value ,the sensitivity deviation of new BPM is less than 0.5% in the vertical direction and less than 2.8% in the horizontal direction .
Beam instrumentation system development and commissioning in ssrf

Y. B. Leng,W. M. Zhou,Y. Z. Chen,K. R. Ye,R. X. Yuan,Y. B. Yan,Y. Zou,G. Q. Huang,G. B. Zhao,Z. C. Chen,L. Y. Yu,J. Chen,J. Yu,C. X. Yin,L. Y. Zhao,D. K. Liu,P. R. China

2008-01-01

Abstract:In recent months the first beams have been stored in the Storage Ring of the Shanghai Synchrotron Radiation Facility (SSRF). The brief introduction will be given of the beam diagnostics system development. The initial commissioning results including beam profile monitors, beam position monitors (BPMs), DC current monitors (DCCT), and synchrotron radiation monitor (SRM) will be reported in this paper. SYSTEM OVERVIEW SSRF is a third generation light source, consisting of a 150MeV linear accelerator (LINAC), a LINAC to booster transfer line (LTB), a full energy booster (BS), a booster to storage ring transfer line (BTS), and a 3.5GeV storage ring (SR) [1]. Table 1 shows the specification of the various diagnostics systems. Table 1: SSRF Beam Instrumentation Specifications Measurement Specification Beam position Resolution 100μm@2Hz Beam profile Resolution 200μm@2Hz Bunch charge Relative accuracy 2% Energy Relative accuracy 0.1% LINAC LTB BTS Emmitance Relative accuracy 10% Beam position Resolution 100μm@1.67MHz Beam profile Resolution 200μm@2Hz DC current Resolution 50μA@10kHz BS Tune Resolution 0.001 Beam position Resolution 10μm@694kHz Resolution 1μm@10kHz Beam profile Resolution 10μm Beam length Resolution 2ps DC current Resolution 10μA@1Hz SR Tune Resolution 0.0001 To meet this specification a beam instrumentation system, consisting of 257 sensors and 1 dedicated diagnostics beam line, has been developed and implemented. Table 2 gives a summary of the various subsystems in all locations. Table 2: SSRF Beam Instrumentation sensors distribution
Application and Design of Photon Beam Position Monitor in HLS

BG Sun,DH He,P Lu,Y Wang,HL Xu,SF Lin,JH Wang,Y Cao,JH Li,P Zheng,CH Zhang

DOI: https://doi.org/10.1109/nssmic.2004.1462588

2004-01-01

Abstract:This paper described the design of a split photon beam position monitor in HLS (Hefei Light Source). The two methods of position processing are given and compared. The monitor was tested and calibrated, the results are well watched with the computed results. The photon beam position monitor has been used in a slow local orbit feedback system. The result of the slow local orbit feedback was given.
Development of Button-Type Pickup for SSRF Ring

Zhao Guo-Bi,Yuan Ren-Xian,Chen Zhi-Chu,Zhou Wei-Min,Leng Yong-Bin

DOI: https://doi.org/10.13538/j.1001-8042/nst.25.060103

2014-01-01

Abstract:In building Shanghai Synchrotron Radiation Facility (SSRF), in order to reduce or eliminate the unnecessary sources of beam motion, the precise and stable beam position measurement system in the feedback system was required. In this study, we focused on theoretical analysis of the electrode of beam position monitor (BPM). Simulations, including analytic derivations of the propagation impedance and the distribution inductance, were performed. The BPM was designed based on the results and the acceptance measurements of the impedance and the inductance by using the time domain reflection (TDR) with a network analyzer. It has been proved in years of operations that the BPM system meets the requirement of the resolution of sub-micron.
Beam Position Monitor Design for a Third Generation Light Source

Zhichu Chen,Yongbin Leng,Kairong Ye,Guobi Zhao,Renxian Yuan

DOI: https://doi.org/10.1103/physrevstab.17.112801

2014-01-01

Physical Review Special Topics - Accelerators and Beams

Abstract:The measurement of the beam orbit plays a very important role in particle accelerators. The button-type beam position monitor (BPM) was designed for the Shanghai Synchrotron Radiation Facility to reduce the impedances and to guarantee a high resolution of the measurement. Position resolution, beam impedance, higher-order mode, and impedance matching have been studied during the design based on the physical parameters of the storage ring at the Shanghai Synchrotron Radiation Facility. Meanwhile, an analytic formula of the BPM broadband impedance was derived based on a resistor-capacitor equivalent circuit. Thus, the impedance of the BPM could be analyzed quantitatively by simply measuring the capacitance of the electrode. This formula had been verified by comparing the results of the calculations of the formula and the simulations in MAFIA.
Monitoring the Beam Profile in Hls with Synchrotron Light

ZG Fang,GC Wang,XF Yan,JH Wang,DH Zhang,YH Zhou,F Zhao,RS Xie,BG Sun,JQ Wu

DOI: https://doi.org/10.1016/0168-9002(95)00860-8

1996-01-01

Abstract:The beam profile monitor built for HLS (Hefei Light Source) is presented. The monitor is composed of an imaging optical system, a commercial CCD TV camera as a detector, an electronic circuit, and a computer to calculate the beam dimensions. This technique has the ability to get the emittance of HLS with the superior resolution, to monitor the beam orbit and beam instability as well.
SYNCHROTRON LIGHT DIAGNOSTIC BEAMLINE DESIGN FOR HEPS STORAGE RING*

Dechong Zhu,Jianshe Cao,Yanfeng Sui,Junhui Yue

DOI: https://doi.org/10.18429/jacow-ipac2019-wepgw062

2019-01-01

Abstract:High Energy Photon Source (HEPS) is a 6 GeV ultralowemittance storage ring light source to be built in Beijing, China. With a multiple-bend achromat lattice design, the storage ring is expected to achieve an ultralow emittance of 34 pm.rad. The horizontal and vertical beam sizes will be in the sub-10 μm level. Beam emittance will be measured with x-ray diagnostic beamline at a low dispersion bending magnet source point. A visible light beamline will be designed to measure the bunch length and purity. In this paper, we will introduce the x-ray beamline, which combine with different techniques to resolve beam sizes and emittance.
Photon Beam Position Monitor for Hefei Light Source Undulator Beamline

Bao-gen SUN,Li-ming GU,Tian-ji MA,Ping LU,Ji-gang WANG,Lei-lei TANG

2009-01-01

Abstract:This paper describes the development of blade-type photon beam position monitor in undulator beamline at HLS (Hefei Light Source) and the photon beam position measurement system. For different gaps of undulator, the calibration of the monitor was carried out. The sensitivity and center positions of photon beam position monitor were measured for different gaps, for example, the horizontal sensitivity and vertical sensitivity are 0.001 5 mm~(-1) and 0.852 2 mm~(-1) at 40 mm gap. In order to improve the photon beam position monitor, a staggered blade-type photon beam position monitor was introduced. At 40 mm gap, the horizontal sensitivity of the new monitor is 0.551 mm~(-1).
DESIGN OF CAVITY BEAM QUADRUPOLE MOMENT MONITOR AT HLS

Qinghua Luo,Qika Jia,Baogen Sun,Ze Zhou

2011-01-01

Abstract:Traditional ways to get beam emittance of linacs, such as multi-slits method, are destructive and then not able to be used in on-line beam diagnostics. To meet the requirements of XFEL equipments and improve the quality of electron beam, non-destructive on-line beam emittance measurement methods basing on getting the quadrupole moment of a beam non-destructively are then required. An advanced way to pick up beam information non-destructively with great precision is making use of eigenmodes of resonant cavities. High brightness injector at Hefei light source is used to study FEL based on photocathode RF electron gun. Cavity beam quadrupole moment monitor system designed for the high brightness injector consists of a square pill-box cavity used to pick up quadrupole signal, a cylindrical pill-box reference cavity, a waveguide coupling network that can suppress monopole and dipole signal, and a superheterodyne receiver used as front-end signal processing system. The whole system works at 5.712 GHz. Focusing strength of quadrupole magnet is adjust to construct a matrix which can be used to work out beam parameters.
Design And Simulation Of Beam Position Monitor For 20omev Linac In Hls

Jh Li,Bg Sun,Dh He,P Lu,Y Wang,Jh Wang,K Jin,Y Cao,P Zheng

2004-01-01

Abstract:In order to improve injection efficiency of HLS(Hefei Light Source), an appropriate BPM (Beam Position Monitor) is needed to provide the transverse positions and longitudinal phases of Linac and transfer line beam. The original stripline BPM for HLS Linac, which is 20.8 degrees in azimuthal angle and has a poor performance in coupling signals on electrodes, is redesigned and calculated through Mafia([1]) and CST Microwave Studio([2]). The new stripline BPM structure, which is 60 degrees and 183.8mm long, has a better performance in time response, spectrum, linearity and sensitivity when a beam passes by. Lastly, the position resolution and time resolution of the new structure is theoretically calculated, which meets the requirement of HLS Linac and transfer line.
Development Of A Split Photon Beam Position Monitor For Hls

Bg Sun,Dh He,P Lu,Jh Wang,Cl Guo,Y Wang,Y Cao,Jh Li,P Zheng

DOI: https://doi.org/10.3321/j.issn:0254-3052.2004.02.021

2004-01-01

Abstract:This paper described the development of a split photon beam position monitor of HLS (Hefei Light Source). The main performances (e.g. sensitivity, position offset and linearity range) were analyzed. The performances of this device were tested, the results are well matched with the calculated results.
Photon Beam Position Monitor with Spring System in HLS

LIN Shun-fu,SUN Bao-gen,GAO Hui,LU Ping,SHEN Chao-bo,BAO Xun

2007-01-01

High Power Laser and Particle Beams

Abstract:A new wire photon beam position monitor with a spring system was designed and installed in the machine diagnostic beamline in Hefei Light Source(HLS).The linearity range is 4 mm,and the sensitivity is about 0.197 9 mm-1.The beam current has a little effect on the synchrotron radiation vertical size.The signal-to-noise ratio and the linearity can be improved,but the sensitivity decreases with a positive bias voltage applied to the copper block.
Design and Simulation of Beam Position Monitor for 200 MeV Linac in HLS

Li, J.H.,Sun, B.G.,He, D.H.,Lu, P.

DOI: https://doi.org/10.1109/nssmic.2004.1462589

2004-01-01

Abstract:In order to improve injection efficiency of HLS (Hefei Light Source), an appropriate BPM (beam position monitor) is needed to provide the transverse positions and longitudinal phases of linac and transfer line beam. The original stripline BPM for HLS Linac, which is 20.8 degrees in azimuthal angle and has a poor performance in coupling signals on electrodes, is redesigned and calculated through Mafia and CST Microwave Studio. The new stripline BPM structure, which is 60 degrees and 183.8 mm long, has a better performance in time response, spectrum, linearity and sensitivity when a beam passes by. Lastly, the position resolution and time resolution of the new structure is theoretically calculated, which meets the requirement of HLS Linac and transfer line.

Design and Fabrication of Button-Style Beam Position Monitors for the HEPS Synchrotron Light Facility

Design of Button Beam Position Monitor for Hefei Light Source

Optimization of the Cavity Beam-Position Monitor System for the Shanghai Soft X-ray Free-Electron Laser User Facility

Design of the Button-Type Beam Position Monitor for the Electron Storage Ring of Hefei Advanced Light Facility

SXFEL LINAC BPM SYSTEM DEVELOPMENT AND PERFORMANCE EVALUATION ∗

Beam instrumentation system for shanghai soft x-ray fel test facility*

Button-Type Beam Position Monitor Development for Fourth-Generation Synchrotron Light Sources: Numerical Modeling and Test Bench Measurements

Design of fast beam transverse profile monitor in electron storage ring

Calibration of Button Type Beam Position Monitor for HLS Ⅱ

Beam instrumentation system development and commissioning in ssrf

Application and Design of Photon Beam Position Monitor in HLS

Development of Button-Type Pickup for SSRF Ring

Beam Position Monitor Design for a Third Generation Light Source

Monitoring the Beam Profile in Hls with Synchrotron Light

SYNCHROTRON LIGHT DIAGNOSTIC BEAMLINE DESIGN FOR HEPS STORAGE RING*

Photon Beam Position Monitor for Hefei Light Source Undulator Beamline

DESIGN OF CAVITY BEAM QUADRUPOLE MOMENT MONITOR AT HLS

Design And Simulation Of Beam Position Monitor For 20omev Linac In Hls

Development Of A Split Photon Beam Position Monitor For Hls

Photon Beam Position Monitor with Spring System in HLS

Design and Simulation of Beam Position Monitor for 200 MeV Linac in HLS