Abstract:In recent years, research has begun to focus on the development of non-resonant elliptical vibration-assisted cutting (EVC) devices, because this technique offers good flexibility in manufacturing a wide range of periodic microstructures with different wavelengths and heights. However, existing non-resonant EVC devices for diamond turning can only operate at relatively low frequencies, which limits their machining efficiencies and attainable microstructures. This paper concerns the design and performance analysis of a non-resonant EVC device to overcome the challenge of low operational frequency. The structural design of the non-resonant EVC device was proposed, adopting the leaf spring flexure hinge (LSFH) and notch hinge prismatic joint (NHPJ) to mitigate the cross-axis coupling of the reciprocating displacements of the diamond tool and to combine them into an elliptical trajectory. Finite element analysis (FEA) using the mapped meshing method was performed to assist the determination of the key dimensional parameters of the flexure hinges in achieving high operational frequency while considering the cross-axis coupling and modal characteristics. The impact of the thickness of the LSFH on the sequence of the vibrational mode shape for the non-resonant EVC device was also quantitatively revealed in this study. Moreover, a reduction in the thickness of the LSFH can reduce the natural frequency of the non-resonant EVC device, thereby influencing the upper limit of its operational frequency. It was also found that a decrease in the neck thickness of the NHPJ can reduce the coupling ratio. Experimental tests were conducted to systematically evaluate the heat generation, cross-axis coupling, modal characteristics and diamond tool’s elliptical trajectory of a prototype of the designed device. The test results showed that it could operate at a high frequency of up to 5 kHz. The cross-axis coupling ratio and heat generation of the prototype are both at an acceptable level. The machining flexibility and accuracy of the device in generating microstructures of different wavelengths and heights through tuning operational frequency and input voltage have also been demonstrated via manufacturing the micro-dimple arrays and two-tier microstructured surfaces. High-precision microstructures were obtained with 1.26% and 10.67% machining errors in wavelength and height, respectively.

Fabrication of Periodic Nanostructure Using a Multi-Tip Diamond Tool: Depth Prediction and Material Removal Mechanism

Controllable Diamond Cutting of Structured Surfaces with Subnanometric Height Features on Silicon

Fabrication of three-dimensional sin-shaped ripples using a multi-tip diamond tool based on the force modulation approach

Fabrication of Periodic Nanostructures Using AFM Tip-Based Nanomachining: Combining Groove and Material Pile-Up Topographies

Molecular Dynamics Simulations of Ripple Nanostructure Formation During Nanomachining Via Atomic Force Microscopy

Fabrication of Periodic Nanostructures Using Dynamic Plowing Lithography with the Tip of an Atomic Force Microscope

AFM Tip-Based Fabrication of Silicon Nanostructures with Reduced Subsurface Amorphous Layers

A New Diamond Machining Approach for Extendable Fabrication of Micro-Freeform Lens Array

Systematic Modeling and Rapid Control for Diamond Machining of Periodical Optical Surface

Force Servo Nano-Precision Diamond Cutting of Freeform Surfaces on a Micro-Precision Machine

Fabrication of Sinusoidal-Shaped Multi-Tip Diamond Tools by a Focused Ion Beam Machining Process

Fabrication of Periodic Nanostructures for SERS Substrates Using Multi-Tip Probe-Based Nanomachining Approach

Towards Understanding the Machining Mechanism of the Atomic Force Microscopy Tip-Based Nanomilling Process

Sub-Diffraction Limited Nanogroove Fabrication of 30 Nm Features on Diamond Films Using 800 Nm Femtosecond Laser Irradiation

Fabrication of Large Scale Nanostructures Based on a Modified Atomic Force Microscope Nanomechanical Machining System.

AFM tip-based mechanical nanomachining of 3D micro and nano-structures via the control of the scratching trajectory

Controlled Nanodot Fabrication by Rippling Polycarbonate Surface Using an AFM Diamond Tip.

Fabrication of Micro-Nano Hierarchical Grating Using Revolving Trajectory of Nanoindenter

A High-Frequency Non-Resonant Elliptical Vibration-Assisted Cutting Device for Diamond Turning Microstructured Surfaces

Three-Dimensional Molecular Dynamics Simulation of Nanostructure for Reciprocating Nanomachining Process

Fabrication of hierarchical micro-groove structures by vibration assisted end fly cutting